Charging The Battery Pack - Flymo Contour Cordless 24 V Traduction Du Mode D'emploi Original

3. Only use the replacement cutting line specified for this
product.
4. Only use replacement parts and accessories recom-
mended by Husqvarna UK Ltd.
5. After any maintenance in dealing with the cutting line,
always return the product to its normal operating posi-
tion before switching on.
6. To avoid the risk of injury keep fingers and hands clear
of the line cutter on the leading edge of the guard.
Battery Pack Care
1. If over a period of time the Battery Pack quickly runs
down after a full 6 hour charging period, a
replacement Battery Pack is needed.
2. There will be some charge present in the Battery Pack
but to ensure maximum running time, charge your
Battery Pack for 6 hours before first use.
3. To prevent permanent Battery Pack damage, never
store in a discharged condition.
4. Contact your local approved service centre/dealer/
distributor for a replacement Battery Pack and for safe
disposal of your old Battery Pack.
5. Battery
24 Volt 1.6 AmpHour
Sealed for Life
Assembly of Switch Handle to Tube (A1)
• Ensure that the internal cable is not twisted.
1. Insert the tube into the switch handle.
2. Push until it clicks into position.
• ENSURE THAT THE TUBE IS FULLY LOCATED BY
ATTEMPTING TO REMOVE IT.
Assembly of Trimmer Head to Tube (A2)
• Ensure that the internal cable is not twisted.
1. Insert the tube into the trimmer head.
2. Push until it clicks into position.
• ENSURE THAT THE TUBE IS FULLY LOCATED BY
ATTEMPTING TO REMOVE IT.
Wheel Assembly (B1) & (B2)
1. Attach the wheel to the trimmer making sure that it is
located into the BOTTOM groove on the trimmer head
as illustrated in Fig B1.
2. Clip the wheel together on each side making sure it is
secure (B2).
3. The wheel should turn freely.
Plant Guard Assembly (B3) & (B4)
1. Open the plant guard as illustrated in Fig B3 and place
into the TOP groove on the trimmer head. Rotate the
plant guard clockwise until it CLICKS into its parked
position (B4).
Safety Guard Assembly (C1) & (C2)
1. Locate the safety guard over the cutting head. Ensure
the nylon line is fed through the hole in the safety guard
as illustrated in Fig C1.
Initial Charging Procedure
1. Use the charger indoors only.
2. Ensure the charger is not exposed to moisture. Keep
the charger and the Battery Pack dry at all times. Keep
the charger well ventilated during charging.
3. Attach the charger connector (F1) to the Battery Pack.
4. Plug the charger (F2) into a suitable household electrical
wall socket and switch on.
5. The red indicator lamp (F3) glows continuously during
charging.
6. Full charge will be achieved in 3 hours after which the
indicator lamp on the charger (F3) will turn to green.
During charging the charger becomes warm. This is
normal and means the charger is operating correctly.
5012693-01 Contour Cordless 24V Euro.indb 2
Battery Pack
"High Power"
No maintenance required
Assembly Instructions

Charging the Battery Pack

ENGLISH – 2
7. Clean unit with a dry cloth. Never use metal objects to
clean the unit.
8. Inspect and maintain the trimmer regularly.
Any repairs must be carried out by an authorised
repairer.
9. Store the product in a cool, dry place and out of reach
of children. Do not store the product outdoors.
10. Allow the product to cool for at least 30 minutes before
storing.
• IMPORTANT
DISPOSE OF YOUR OLD BATTERY PACK SAFELY
DO NOT CUT OPEN, BURN OR INCINERATE.
Winter Storage
1. Fully charge for 6 hours before winter storage.
2. Re-charge the Battery Pack every 3 to 4 months for
a full 6 hour charging period to top up the battery
charge during winter storage.
3. Avoid extended storage without re-charge.
4. Store in a cool dry place.
For further information on Battery Pack replacement
contact your local dealer.
2. Push into location and turn safety guard in the direction
illustrated in Fig C2, until a click is heard and the safety
guard is securely locked in position.
• ENSURE THE SAFETY GUARD IS SECURELY IN
PLACE BY ATTEMPTING TO TWIST GUARD.
Steady Handle Assembly (D)
1. Pull the steady handle release lever towards the handle
grip.
2. Depress the two buttons on the side of the steady
handle.
3. Locate the buttons into the main handle and release the
lever.
4. Adjust the steady handle to the most comfortable
operating position by pulling the release lever and
moving the handle.
Height Adjustment (E)
1. Turn height adjuster (E1) in the direction indicated to
un-lock (E2).
2. Adjust the length of the tube to the most comfortable
operating position.
3. Turn height adjuster in the opposite direction to
lock (E3).
• ENSURE THAT THE TUBE IS FULLY SECURED.
Re-Charging the Battery Pack
1. Re-charge the Battery Pack as soon as the cutting
power of your trimmer begins to die and slow down.
2. Avoid running the Battery Pack into "deep" discharge,
i.e. avoid flattening the Battery Pack completely.
3. Follow the procedure outlined in the Initial Charging
Procedure.
4. Charging the Battery Pack according to these instruc-
tions should ensure maximum battery life.
Battery Pack Assembly (G)
1. Attach the Battery Pack as illustrated in Fig G, ensuring
that it clicks into position and is located firmly.
2. To remove, press the two buttons (G1) on either side of
the Battery Pack and slide off.
16.10.15 11:27