Peavey PV 118 D Mode D'emploi page 26

Cleaning
®
Never clean the PV 118D while plugged in or turned ON! When the unit has been fully disconnected from AC power sources,
use a dry cloth or a plastic bristle brush to remove soil or other dirt. Never use strong solvents on the PV
could damage the cabinet. Do not allow ANY fluids to drip inside the PV ® 118D.
Architectural and Engineering Specifications
The powered loudspeaker system shall have a frequency range from 38 Hz to 120 Hz. The peak SPL with inaudible
distortion shall reach 119 dB with music as a source, when measured at a distance of 1 meter and driven to full output
capacity. The system shall utilize an 18" heavy-duty woofer.
The powered loudspeaker system shall have a two medium impedance input connectors consisting of one female XLR
and one 1/4" TRS phone jack located on the rear panel. A volume control shall be provided.
The rear panel shall also provide a balanced XLR line-level output. A switch shall control whether the output is a full
bandwidth (thru) or a high-pass output with a corner frequency of 120 Hz, and a 4th order Linkwitz-Riley filter characteristic.
The system power amplifiers shall have an unfiltered frequency response of 10 Hz to 30 kHz which deviates no more
than +0, -1 dB up to rated power, a damping factor greater than 100 @ 1 kHz into 8 ohms, hum and noise better than 90
dB below rated power, and THD and IMD of less than 0.1%. Each woofer amplifier shall be capable of 150 W continuous
into an 8-ohm nominal load, providing a total of 300 watts continuous into the dual voice-coil woofer. Both amplifier
channels shall incorporate independent DDT compression.
The enclosure shall be constructed of 3/4" MDF. A metal handgrip shall be provided on each side of the enclosure.
A powder-coated metal grille shall be provided for woofer protection. The cabinet shall incorporate a pole mount for
speaker stand use, four sturdy rubber feet for floor standing use.
The outside dimensions shall be: 27" tall x 21.9" wide x 19.6" deep, and the weight shall be 76 lbs. Power
requirements shall be: 100-Watts nominal (1/8 audio power), 100-120 VAC, 50/60 Hz Domestic and 220-240 VAC, 50/60
Hz (Export). The loudspeaker system shall be called the Peavey PV 118D.
Frequency Range, (-10 dB, half space) 38 Hz to 120 Hz
Frequency Response (+/- 3dB anechoic) 46 Hz to 90 Hz
Sensitivity (1w, 1m): 95 dB
Maximum SPL: 119 dB
Transducer Complement: 18" Heavy-duty woofer
with 3" dual voice coils, and 65 oz. magnet
Box Tuning Frequency: Low Frequency Section 46 Hz
Crossover Frequency: 120 Hz
Nominal Impedance (Z): 8 Ohms
Input Connections: Line level XLR jack input,
speaker level 1/4" phone jack input
Peavey Electronics Corporation • 5022 Hartley Peavey Drive • Meridian • MS • 39305
(601) 483-5365 • FAX (601) 486-1278 • 80305569 • www.peavey.com
Peavey PV
SPECIFICATIONS
Features and specifications are subject to change without notice.
EX000075
118D
®
Output Connections: Line-level XLR jack output,
switchable to either Thru mode, or High Pass Filter
mode
Power Amplifier Output:
150 watts continuous RMS into 8 ohms, 300 watts
peak available (times 2) for a total of 300 watts
continuous RMS and 600 watts peak available
power.
Enclosure Materials & Finish: MDF covered in Black
Carpet
Dimensions (H x W x D): 27.00" x 21.88" x 19.63" /
686 mm x 556 mm x 499 mm
Net Weight: 76 lbs. (34.5 kg)
® 118D, as they