Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
8.2 General data
For safety applications up to:
Interlock, no contact, coded:
Level of coding acc. to EN ISO 14119:
Safety parameters:
MTTF
:
D
PFH
:
D
DC:
Mission time:
Operating temperature:
Storage temperature:
Vibration resistance:
Shock resistance:
Pollution degree
8.3 Power supply electrical data
8.3.1 Power supply electrical data
Rated operating voltage U
:
e
Supply voltage tolerance:
Operating current at U
voltage:
e
minimum:
with all outputs at maximum power:
Rated insulation voltage U
:
i
Rated impulse withstand voltage U
imp
External protection fuse:
Overvoltage category:
8.3.2 Electrical data of IS1/IS2/I3/EDM inputs
Rated operating voltage U
:
e1
Rated current consumption:
Switching time EDM state (t
):
EDM
8.3.3 Electrical data of OS1/OS2 safety outputs
Rated operating voltage U
:
e2
Output type:
Maximum current per output I
:
e2
Minimum current per output I
:
m2
Thermal current I
:
th2
Utilization category:
Short circuit detection:
Overcurrent protection:
Resettable internal protection fuse:
Duration of the deactivation impulses at the safety outputs: < 300 μs
Permissible capacitance between outputs:
Permissible capacitance between output and ground: < 200 nF
Response time (tr
) after deactivation of inputs IS1 or IS2: < 15 ms
I
Response time (tr
) after actuator removal:
A
Availability time:
8.3.4 Electrical data of O3 signalling output
Rated operating voltage U
:
e3
Output type:
Maximum current per output I
:
e3
Utilization category:
Short circuit detection:
Overcurrent protection:
Resettable internal protection fuse:
8.3.5 Actuation data
Assured operating distance S
:
ao
Assured release distance S
:
ar
Rated operating distance S
:
n
Rated release distance S
:
nr
Repeat accuracy:
Differential travel:
RFID transponder frequency:
Max. switching frequency:
Minimum distance between two sensors:
8.4 Compliance with standards
EN ISO 14119, IEC 61508-1, IEC 61508-2, IEC 61508-3, IEC 61508-4,
EN ISO 13849-1, EN ISO 13849-2, EN 62061, EN 60947-5-3, EN 60947-5-2,
EN 60947-1, EN 61326-1, EN 61326-3-1, EN 61326-3-2, EN IEC 63000,
ETSI EN 301 489-1, ETSI EN 301 489-3, ETSI 300 330-2, UL 508, CSA 22.2 No.14
8.5 Compliance with directives
Machinery Directive 2006/42/EC, EMC Directive 2014/30/EU, Radio Equipment
Directive 2014/53/EU, RoHS Directive 2011/65/EU, FCC Part 15
9 SPECIAL VERSIONS ON REQUEST
Special versions of the device are available on request.
The special versions may differ substantially from the indications in these operating
instructions.
The installer must ensure that he has received written information from the support
service regarding installation and use of the special version requested.
SIL 3 acc. to EN 62061
PL e, cat. 4 acc. to EN ISO 13849-1
type 4 acc. to EN ISO 14119
high with SM •1T actuators
low with SM •0T actuators
1551 years
1,19E-09
High
20 years
-25 ... +70 °C
(articles ST G••••••)
-35 ... +85 °C
(articles ST G••••MK-T8)
-35 ... +85 °C
10 gn (10...150 Hz) acc. to IEC 60068-2-6
30 gn; 11 ms acc. to EN 60068-2-27
3
24 Vdc
± 15% of U
e
20 mA
550 mA
32 Vdc
:
1.5 kV
1 A type Gg
or equivalent device
III
24 Vdc
2.5 mA
500 ms
24 Vdc
PNP type OSSD
0.2 A
0.5 mA
0.2 A
DC13; U
=24 Vdc, I
=0.2 A
e2
e2
Yes
Yes
0.3 A
< 200 nF
< 50 ms
2 s
24 Vdc
PNP
0.1 A
DC13; U
=24 Vdc, I
=0.1 A
e3
e3
No
Yes
120 mA
SM G•T, SM D•T,
SM E•T actuators
SM L•T actuators
8 mm
14 mm
20 mm
26 mm
11 mm
18 mm
13 mm
20.5 mm
≤ 10 % s
n
≤ 20 % s
n
125 kHz
1 Hz
50 mm
10 DISPOSAL
At the end of service life product must be disposed of properly, according to the
rules in force in the country in which the disposal takes place.
11 SUPPORT
The device has been created for safeguarding people's physical safety, therefore in
case of any doubt concerning installation or operation methods, always contact our
technical support service:
Pizzato Elettrica Srl - Italy
Via Torino, 1 - 36063 Marostica (VI)
Telephone +39.0424.470.930
E-mail tech@pizzato.com
www.pizzato.com
Our support service provides assistance in Italian and English.
12 EC CONFORMITY DECLARATION
I, the undersigned, as a representative of the following manufacturer:
Pizzato Elettrica Srl - Via Torino, 1 - 36063 Marostica (VI) – ITALY
hereby declare that the product is in conformity with whatever prescribed by the 2006/42/
EC Machine Directive. The complete version of the present conformity declaration is
available on our website www.pizzato.com
Marco Pizzato
DISCLAIMER:
Subject to modifications without prior notice and errors excepted. The data given in this sheet
are accurately checked and refer to typical mass production values. The device descriptions
and its applications, the fields of application, the external control details, as well as information
on installation and operation, are provided to the best of our knowledge. This does not in any
way mean that the characteristics described may entail legal liabilities extending beyond the
"General Terms of Sale", as stated in the Pizzato Elettrica general catalogue. Customers/
users are not absolved from the obligation to read and understand our information and
recommendations and pertinent technical standards, before using the products for their own
purposes. Taking into account the great variety of applications and possible connections of
the device, the examples and diagrams given in the present manual are to be considered as
merely descriptive; the user is deemed responsible for checking that the specific application
of the device complies with current standards. This document is a translation of the original
instructions. In case of discrepancy between the present sheet and the original copy, the
Italian version shall prevail. The present manual may not be reproduced, in whole or in part,
without the prior written permission by Pizzato Elettrica.
© 2019 Copyright Pizzato Elettrica. All rights reserved.
10/20
Publicité
Table des Matières
