Bosch PSM 200 AES Notice Originale page 14

14 | English
Changing the sanding sheet (see figure C)
Remove dirt and dust from the sanding plate (7), e.g. with a
brush, before attaching a new sanding sheet.
To ensure optimum dust extraction, make sure that the
punched holes in the sanding sheet are aligned with the
drilled holes in the sanding plate.
The sanding plate (7) is fitted with a hook-and-loop fasten-
ing, allowing sanding sheets with a similar backing to be se-
cured quickly and easily.
Tap the hook-and-loop fastening of the sanding plate (7) be-
fore fitting the sanding sheet (14) to facilitate maximum ad-
hesion.
The power tool is equipped with two sanding sheets. De-
pending on their state of wear, these can also be changed in-
dividually.
Only use the power tool when both sanding sheets are
u
fitted.
Only use sanding sheets with the same grit.
u
Position the sanding sheet (14) so that it is flush with one a
side of the sanding plate (7), then place the sanding sheet
on the sanding plate and press it on firmly.
To remove the sanding sheet (14), take hold of it by an edge
and pull it away from the sanding plate (7).
You can use the Bosch delta sander sanding sheets.
Sanding accessories such as fleece/polishing felt are at-
tached to the sanding plate in the same way.
Choosing the sanding sheet
Different sanding sheets are available, depending on the ma-
terial you are working with and the required surface removal
rate:
Application
Can be used to work on all materials including
wood, paint, filler, varnish, hard and softwood
as well as chipboard and metal
For pre-sanding, e.g. of rough and un-
even beams and boards
For surface sanding and levelling of
slight irregularities
For finishing and fine sanding of hard
woods
For any finishing work, such as polishing (metal and stone in
particular), use fleece/polishing felt.
Different types of fleece and polishing felts should be used
depending on the surface finish required on the workpiece.
Removing the two-piece sanding plate
(see figure D)
❶ Push the SDS slider for sanding plate release (6) all the
way to the right.
❷ Remove the sanding plate (7).
❸ Pull the rear sanding plate (8) downwards by the re-
cessed handles and then pull it off backwards.
1 609 92A 68V | (16.03.2021)
If the front tip of the sanding sheet has worn down, the en-
tire sanding plate can be removed, rotated 120° and put
back on again for reuse.
Fitting the two-piece sanding plate
(see figure E)
❶ First, place the rear sanding plate (8) onto the sanding
plate holder so that the catches fit into the recesses.
Press the sanding plate (8) onto the holder until you
here it click into place.
❷ Attach the front sanding plate (7).
❸ To fix the sanding plate in place, push the SDS slider for
sanding plate release (6) all the way to the left.
Fitting the rectangular sanding plate
(see figures F–G)
❶ First, place the rear sanding plate (9) onto the sanding
plate holder so that the catches fit into the recesses.
Press the sanding plate (9) onto the sanding plate
holder until you hear it click into place.
❷ To fix the sanding plate in place, push the SDS slider for
sanding plate release (6) all the way to the left.
❸ Now check whether the rear part of the sanding plate is
properly engaged by pressing on the rear right and left
part of the rectangular sanding plate.
Removing the rectangular sanding plate
❶ Push the SDS slider for sanding plate release (6) all the
way to the right.
❷ Remove the rectangular sanding plate (9).
Grit
Special Sanding Plates
40–180
You can replace the standard supplied sanding plate (7) with
one of the special sanding plates that are available as ac-
cessories.
Coarse 40
Special sanding plates are fitted in exactly the same way as
the standard supplied sanding plate.
Medium 80, 120
Likewise, each sanding sheet is attached and removed in ex-
actly the same way as the original sanding sheet.
Fine 180
The operation of the special sanding plates is only permitted
with a mounted rear sanding plate (8).
Louvre Sanding Attachment (see figure H)
The louvre sanding attachment (15) allows you to work on
areas that are particularly difficult to reach, such as slats on
windows, cupboards and doors.
Sanding Finger, Flat (see figure I)
The flat sanding finger (17) allows you to work on narrow
slits and tight gaps.
The sanding sheet for the sanding finger (16) is fitted in the
same way as the front sanding sheet (14).
Bosch Power Tools