Evolution R255 SMS Notice Originale page 7

www.evolutionpowertools.com
3) General Power Tool Safety Warnings
(2.4)
[Personal Safety].
a) Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection to prevent injury from
sparks and chippings. Protective equipment such
as dust masks, non-skid safety shoes, hard hat or
hearing protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before connecting to
power source and or battery pack, picking up or
carrying the tool.
Carrying power tools with your finger on the switch
or energising the power tools that have the switch on
invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or key left attached to a rotating part of a
power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts. Loose
clothes, jewellery or long hair
can be caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
that these are connected and properly used.
Use of dust collection can reduce
dust-related hazards.
h) When cutting metal, gloves should be worn
before handling to prevent from getting burnt
from hot metal.
i) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery
handles and grasping surfaces do not allow
for safe handling and control of the tool in
unexpected situations.
4) General Power Tool Safety Warnings
(2.5)
[Power tool use and care].
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better
and safer at a rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on or off. Any power tool that cannot
be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the power tool from the power
source and/or battery pack from the power
tool before making any adjustments, changing
accessories, or storing power tools.
Such preventative safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these Instructions to
operate the power tool. Power tools are dangerous
in the hands of untrained users.
e) Maintain power tools. Check for misalignment
or binding of moving parts, breakage of moving
parts and any other condition that may affect
the power tools operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, taking
into account the working conditions and the
work to be performed. Use of the power tool for
operations different from those intended could result
in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) General Power Tool Safety Warnings
(2.6)
[Service] a) Have your power tool serviced by
a qualified repair person using only identical
replacement parts. This will ensure that the safety of
the power tool is maintained.
If the supply cord of this power tool is damaged,
it must be replaced by a specially prepared supply
cord available through the service organization.
MITRE SAW SPECIFIC SAFETY
(3.5)
• Not to use saw blades manufactured from
high speed steel.
• Use only the saw with guards in good
working order and properly maintained, and
in position.
• Always to clamp work-pieces to
the saw table.
7
EN
ES
DE
FR
IT
PL
PT
RO