Cleaning, Maintenance And Ordering Spare Parts - EINHELL TE-DY 18 Li Mode D'emploi D'origine

6.3 Battery capacity indicator (Fig. 3 /Item 10)
Press the battery capacity indicator switch (11).
The battery capacity indicator (10) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive
discharge and is defective. Do not use or charge
a defective battery pack.
6.4 LED lamp (Fig. 3/Item 9)
The LED light (9) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED light (9) will come on
automatically as soon as you press the On/Off
switch (4).
6.5 Setting the screwing depth (Fig. 4)
Using the depth setting ring (2) with latching
settings you can pre-select the depth to which the
screw is screwed into the workpiece.
PLUS direction: larger screwing depth
MINUS direction: smaller screwing depth
The best way to establish the required setting is
screwing in a screw on a test basis fi rst. Press
the tip of the screw fi rmly against the material
in question until the screwing depth stop (1)
comes up against the workpiece and the coupling
disengages.
6.6 Changing the tool insert
To change the tool insert, rotate the screwing
depth stop (1) with the depth setting ring (2) as far
as the maximum screwing depth and pull off the
tool insert to the front (use pincers if necessary).
6.7 Screws
It is advisable to use self-centering screws (e.g.
Torx, cross recessed head) as these will enable
you to work safely and reliably. Always make sure
that the insert used is of the same size and shape
as the screw.
Anl_TE_DY_18_Li_USA_SPK7.indb 13 Anl_TE_DY_18_Li_USA_SPK7.indb 13
EN
6.8 Removable holding clip (Fig. 1 / Item 6)
When the holding clip (6) is fi tted, the equipment
can be hung e.g. on a belt. The removable holding
clip can be screw-fi tted to either the left or right-
hand side of the equipment. Fitting is possible but
not necessary.
7. Cleaning, maintenance and
ordering spare parts
HAZARD!
Always take the battery out of the equipment
before starting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment. The ingress of
water into an electric power tool increases the
risk of an electric shock.
7.2 Maintenance
There are no other parts inside the equipment
which require maintenance.
7.3 Ordering replacement parts:
Service
1. If your power tool requires service,
contact an authorized Einhell USA dealer
or call the Einhell USA customer service
center at 1-866-EINHELL
(1-866-346-4355). Only identical
replacement parts should be utilized for
repairs. This will ensure that the safety of the
power tool is maintained.
2. If the battery charger cable is damaged, it
must be immediately replaced to avoid a
hazard. Contact the Einhell USA
service center at 1-866-EINHELL
(1-866-346-4355) for assistance.
- 13 -
customer
®
16.12.2019 15:37:40 16.12.2019 15:37:40