Functional Description; Removing/Inserting The Battery - Milwaukee 2746-20 Manuel De L'utilisateur

FUNCTIONAL DESCRIPTION

7
6
1. Trigger
2. Handle
3. Power/Actuation
selection
4. Hook
5. Pusher release button
ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.

Removing/Inserting the Battery

To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Installing/Removing Fastener Strips
Always remove battery pack before
WARNING
changing or removing fasteners.
Always wear safety goggles or glasses with side
shields.
To install fastener strips:
1. Remove battery pack.
2. WARNING! Always point the tool away from yourself
and others when installing fasteners. Failure to do
so could result in injury.
3. Press the magazine release button and slide the
magazine open. Place the tip of the fasteners into the
bottom slot of the magazine; then lay the fasteners
flat against the magazine. The heads must fit into the
grooves. WARNING! Use only recommended fasten-
ers of the correct size, length, collation angle and head
type as indicated on the tool's nameplate. Other fas-
teners could result in tool malfunction, leading to injury.
1
2
3
10
9
8
6. Workpiece contact
7. Jam latch
8. Depth adjustment
9. LED
10. Workpiece contact
tip storage
4. Slide the magazine closed.
To remove fastener strips:
1. Remove battery pack.
2. WARNING! Always point the tool away from yourself
4
and others when installing fasteners. Failure to do
so could result in injury.
3. Press the magazine release button and slide the
magazine open.
4. Remove the fasteners.
WARNING
with side shields. The operator and other people
5
in the work area must wear eye protection in ac-
cordance with ANSI Z87.1. Eye protection does not
fit all operators in the same way. Make sure the eye
protection chosen has side shields or provides
protection from flying debris both from the front
and sides. The employer is responsible for enforc-
ing the use of eye protection by the operator and
other people in the work area. When required, wear
head protection in accordance with ANSI Z89.1.
To reduce the risk of injury to yourself and others,
test the tool before beginning work each day ac-
cording to the "Required Daily Testing" section.
Do not use the tool unless you thoroughly under-
stand the actuation mode selected.
Remove battery pack and fasteners before leaving
the work area, moving the tool to another location,
or handing the tool to another person. Failure to do
so could result in serious injury.
Do not use this tool for fastening electrical
cables. It is not designed for electric cable
installation and may damage the insulation of
electric cables thereby causing electric shock
or fire hazards.
NEVER wedge or hold back the workpiece contact
mechanism during operation of the tool. Never
attempt to clear a jammed workpiece contact by
grasping the discharge area of the tool. Doing so
could result in serious injury.
To avoid serious injury, do not attempt to prevent
the recoil by holding the tool too firmly against
the work. Keep face and body away from the tool.
During normal use, the tool will recoil immediately
after driving a fastener. This is a normal function
of the tool. Restriction to the recoil can result in a
second fastener being driven when the tool is in
Contact Actuation mode. Grip the handle firmly,
let the tool do the work, and do not place a second
hand on top of the tool.
Power/Actuation Selection
1. Install battery pack.
2. Press and hold the Power button
tool (the Power button's green LED ring will light).
The Battery LED indicates when the battery level
is sufficient to operate the tool.
Power
button
Actuation
Indicator
LED
4
OPERATION
To reduce the risk of injury, always
wear safety goggles or glasses
to turn on the
Battery
LED
Actuation
Indicator
LED