Problem Chart; Technical Specifications - Omnitronic HDA Série Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

PROBLEM CHART

PROBLEM:
No power.
No sound.
Noise.
Fan does not work, LEDs
do not light up
Protect
LED
lights
permanently

TECHNICAL SPECIFICATIONS

Power supply:
Nominal power output:
Frequency range:
Damping-factor:
Distortion factor:
Signal to Noise Ratio:
Min. input sensitivity:
Input impedance:
Output impedance:
Slew-rate:
LED indicators
(per channel):
Dimensions:
Minimum mounting
depth:
Please note: Every information is subject to change without prior notice. 17.11.2006 ©
CAUSE:
• The power-cord is not connected.
• The power-cord of the respective
device is not connected properly or
not connected at all.
• The connection-socket or the plug is
dirty.
• The input-signal is too strong.
• The power-cord is not connected.
up
• Inputs receive DC-voltage.
• Amplifier is overheated due to
impurities.
• Impedance of speakers too low
• Short-circuit in speaker connection or
in speakers
• Technical default of amplifier
HDA-2.2
230 V AC, 50 Hz ~ 230 V AC, 50 Hz ~
2 x 100 W+200 W
2 x 200 W+300 W
20 - 20 000 Hz
20 - 20 000 Hz
>250
>250
0,05 %
0.05 %
>95 dB
>95 dB
0.775 V RMS
0.775 V RMS
10 kOhm
10 kOhm
(unbalanced),
(unbalanced),
20 kOhm
20 kOhm
(balanced)
(balanced)
>0.02 Ohm
>0.02 Ohm
20 V/µ sec
20 V/µ sec
Clip, Protect,
Clip, Protect, Signal
Signal
450 x 482 x 90 mm 450 x 482 x 90 mm
470 mm
470 mm
• Check the power-cord and any
extension-cables.
• Check the power-cord and if the
plugs are tightly connected with the
sockets.
• Clean the socket and/or the plug.
• Reduce the input-signal via the Gain-
control.
Please check if the power is available
• Switch amplifier off and have the
device checked by a service-
technician.
• Clean the fan-grille.
• Connect other speakers.
• Check speakers.
• Switch amplifier off and have the
device checked by a service-
technician.
HDA-4.3
HDA-6.5
230 V AC, 50 Hz ~ 230 V AC, 50 Hz ~
2 x 300 W+500 W
20 - 20 000 Hz
>250
0.05 %
>95 dB
0.775 V RMS
10 kOhm
(unbalanced),
20 kOhm
balanced)
>0.02 Ohm
20 V/µ sec
Clip, Protect,
Signal
450 x 482 x 90 mm 450 x 482 x 90 mm
470 mm
26/34
REMEDY:
HDA-7.6
2 x 350 W+600 W
20 - 20 000 Hz
>250
0.05 %
>95 dB
0.775 V RMS
10 kOhm
(unbalanced),
20 kOhm
balanced)
>0.02 Ohm
20 V/µ sec
Clip, Protect,
Signal
470 mm
10452350_V_1_0.DOC

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Hda-2.2Hda-4.3Hda-6.5Hda-7.6

Table des Matières