Noise/Vibration Information; Changing The Tool; Battery Charging - Bosch GOP 18V-28 Professional Notice Originale

OBJ_BUCH-2789-002.book Page 18 Thursday, June 30, 2016 9:37 AM
18 | English
Cordless Multi-Cutter
Permitted ambient
temperature
– during charging
1)
– during operation and
during storage
Recommended batteries
Recommended chargers
1) Limited performance at temperatures <0 °C
Technical data determined with battery from delivery scope.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-4.
Typically the A-weighted noise levels of the product are:
Sound pressure level 84 dB(A); Sound power level 95 dB(A).
Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-4:
2
Sanding: a =3.4 m/s , K=1.5 m/s
h
Sawing with plunge cut saw blade: a
Sawing with segment saw blade: a
2
Scraping: a =8.6 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with an-
other. It may be used for a preliminary assessment of ex-
posure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work
patterns.
Assembly

Battery Charging

 Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
1 609 92A 3BT | (30.6.16)
Note: The battery supplied is partially charged. To ensure full
GOP 18V-28
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
°C 0...+45
ducing its service life. Interrupting the charging procedure
does not damage the battery.
°C –20...+50
Removing the battery
GBA 18V ...
GBA 18V ... W The battery 3 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
AL 18..
unlocking button 11 unintentionally. As long as the battery is
GAL 18.. W
inserted in the power tool, it is held in position by means of a
GAL 3680
spring.
To remove the battery 3, press the battery unlocking button
11 and pull the battery out of the power tool toward the rear.
Do not exert any force.
Battery Charge-control Indication
The three green LEDs of the battery charge-control indicator
5 indicate the charge condition of the battery 3. For safety
reasons, it is only possible to check the status of the charge
condition when the machine is at a standstill.
Press button 6 to indicate the charge condition. This is also
possible when the battery 3 is removed.
LED
2
,
Continuous lighting 3 x green
2 2
=8 m/s , K=1.5 m/s ,
h
Continuous lighting 2 x green
2 2
=5.7 m/s , K=1.5 m/s ,
h
2
. Continuous lighting 1 x green
Flashing light 1 x green
When no LED lights up after pushing button 6, then the bat-
tery is defective and must be replaced.

Changing the Tool

 Before any work on the machine itself (e. g. mainte-
 Wear protective gloves when changing application
Selecting the Application Tool/Accessory
Accessory
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
tools/accessories. Contact with the application tool/
accessory can lead to injuries.
Capacity
≥2/3
≥1/3
<1/3
Reserve
GOP 18V-28
Bosch Power Tools