Grounding Instructions - Waring Commercial MX1300XTX Manuel D'utilisation

GROUNDING INSTRUCTIONS

• For your protection, Waring ® blenders are equipped with a 3-conductor
cordset having a molded 3-prong grounding-type plug, and should be
used in combination with a properly connected grounding-type outlet as
shown in Figure A. If a grounding-type outlet is not available, an adapter,
as shown in Figure B, may be used to enable a 2-slot wall outlet to be
used with a 3-prong plug.*
As shown in Figure C, the adapter must be grounded by attaching its
grounding lug under the screw of the outlet cover plate.
CAUTION: Before using an adapter, it must be determined that the
outlet cover plate screw is properly grounded. If in doubt, consult a
licensed electrician.
Never use an adapter unless you are sure it is properly grounded.
*NOTE: Use of an adapter is not permitted in Canada.
NOTE: User-installed cord set plugs are not permitted in Europe.
MX1300XTX/MX1300XTP/MX1300XTS & MX1500XTX/MX1500XTP/MX1500XTS
BLENDER SPECIFICATIONS
• C apacity: 64 oz. Working Capacity (48 oz. capacity with MX1300XTP &
MX1500XTP versions)
• Switch Settings: Reprogrammable
• V ariable Motor Speed: Minimum 3,000 RPMs / Maximum 20,000 RPMs
(30,000 RPM with Pulse)
• Rating: 120 Volts - 13.0 Amps
• Base Material: Polycarbonate
• P olycarbonate Sound Enclosure included with MX1500XTX/ MX1500XTP/
MX1500XTS versions only
• Bearing: High Precision Ball Bearing
• Cord: 6-Foot Three-Conductor Ground Core with Strain Relief in Base
• Overall Height: 21 Inches
• Operating Cycle: 1 minute ON/3 minutes OFF
• Weight: 18 lbs
• ETL , NSF listed
c us
4
1. Plug the power cord into AC outlet. Press the On/Off
turn the unit on. The blue LCD backlight will turn on and the words
WARING COMMERCIAL will appear, indicating that the power is on.
After 5 seconds, the blender enters standby mode.
NOTE: In standby mode, the blender is awaiting directions and will read
PRESS ANY BUTTON TO BLEND.
2. The motor speed can be adjusted by pressing the
buttons. Speed ranges from 15% to 100%.
100% 20,000 RPMs
50% 10,000 RPMs
15% 3,000 RPMs
The Speed Up button will increase the motor speed display in 1%
increments and the Speed Down
speed display in 1% increments. Holding down either button will quickly
scroll through speeds.
Using the Speed Up and Speed Down
speed. If no speed is selected, motor will default to 100%.
NOTE: The motor does not run at the newly set speed until the Start/
Stop button is pressed. If Start/Stop
within 5 seconds, the new speed setting will be stored for next use and
the blender will return to standby mode; the display will once again read
PRESS ANY BUTTON TO BLEND.
3. Press Start/Stop button to turn the blender on. Blender will run
continuously at the set speed. The LCD will display the motor speed in
percentage. Default speed (percentage) is at 100%. Motor speed can be
changed while blender is running by simply pressing Speed Up
Speed Down button.
4. To stop continuous blending operation, press Start/Stop
press any of the program buttons.
PULSE FEATURES
Your unit comes equipped with two Pulse options: Normal Pulse
Maximum Pulse . Note: The Pulse buttons are momentary switches –
once released, the unit will shut off.
1. To use Max pulse option, press the
at 150% speed. The LCD will read MAX PULSE SPEED: 150%.
2. To use Normal pulse option, press the
at 100% speed. The LCD will read NORM PULSE SPEED: 100%.
3. The blender allows you to set the pulse to your desired speed. While
blending at Normal pulse speed, the motor can be adjusted. To do this,
hold the Pulse button and press Speed Up
OPERATION
button to
or
button will decrease the motor
buttons, set desired motor
button is not pressed
button. This will run the motor
button. This will run the motor
or Speed Down
5
Speed
or
button or
and