Noise/Vibration Information; Battery Charging; Battery Charge Indicator - Bosch GSA 18 V-LI C Professional Notice Originale

14 | English
Reciprocating saw
Max. cutting depth
– In wood
– In steel (unalloyed)
– Pipe diameter
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
B)
– during operation and
during storage
Recommended batteries
Recommended chargers
A) Depends on battery in use
B) Limited performance at temperatures <0 °C
Technical data determined using the battery that comes with the
product.

Noise/vibration information

Noise emission values determined according to
EN 62841-2-11.
Typically the A-weighted noise level of the power tool is:
Sound pressure level 82 dB(A); sound power level
93 dB(A). Uncertainty K = 5 dB.
Wear hearing protection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-11:
Cutting boards with saw blade S 644 D:
2 2
a = 9 m/s , K = 1.5 m/s ,
h,B
Cutting wooden beams with saw blade S 611 DF:
2 2
a = 8 m/s , K = 1.5 m/s .
h,WB
(The values relating to cutting boards with a saw blade are
valid for a thickness of 20 mm.)
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
1 609 92A 4TC | (02.04.2019)
Implement additional safety measures to protect the oper-
GSA 18 V-LI C
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
mm 200
and organising workflows correctly.
mm 16
Assembly
mm 100
A)
kg 2.3–3.3
u
°C 0 to +45
°C −20 to +50

Battery Charging

GBA 18V...
u
ProCORE18V...
GAL 18...
GAX 18...
Note: The battery is supplied partially charged. To ensure
GAL 36...
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
u
The battery (4) is equipped with two locking levels to pre-
vent the battery from falling out if the battery release button
(8) is pressed unintentionally. The battery is held in place by
a spring when fitted in the power tool.
To remove the battery (4), press the release button (8) and
pull the battery out of the power tool. Do not use force to
do this.

Battery charge indicator

The green LEDs on the battery charge indicator (11) indic-
ate the battery's state of charge (4). For safety reasons, it is
only possible to check the state of charge when the power
tool is not in operation.
Press the button for the battery charge indicator (10) to
show the state of charge. This is also possible when the bat-
tery is removed.
If no LED lights up after pressing the button for the battery
charge indicator (10), then the battery is defective and must
be replaced.
Battery model GBA 18V... (see figure A)
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
3× flashing green light
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
Capacity
60−100 %
30−60 %
5−30 %
0−5 %
Bosch Power Tools