Operating Instructions - Jensen VM9021TS Guide D'instructions

OPERATING INSTRUCTIONS

Power On / Off
Press the /MUTE button (1) to turn the unit on. The buttons on the
front of the unit light up.
Press and hold the /MUTE button (1) on the front panel or the
POWER button (4) on the remote to power off the unit..
Audible Beep Confirmation
An audible beep tone confirms each function selection. The beep
tone cannot be disabled.
Mute
Press the /MUTE button (1) on the front panel or remote (3)
to mute the volume from the unit. Press the MUTE button
again to restore the volume. The mute icon flashes on the
right side of the screen. Adjusting the volume or using any of
the audio set-up features cancels the mute function.
Playing Source Selection
Press the SRC button (11) on the remote to change between
available playing sources in the following order: TUNER,
DVD, AUX IN or CAMERA (rear view video camera). The
playing mode is displayed on the screen.
Press the MENU/SRC button (11) on the unit to access the
playing source menu. Use the direction buttons on the
joystick (6, 7, 8, 9) or remote control (14, 17, 18, 19, 22) to
select a playing source, then press the >/||
joystick enter button (5) to enter the selected source.
AUX IN Mode
An external peripheral device can be connected to this unit
via RCA output and "AUX-IN".
CAMERA Mode
"CAMERA" mode is only available if the camera is connected
and during reverse driving. To install a rear view video
camera, connect the video input cable to the camera output
cable.
Volume Adjustment
To increase the volume level, press the VOL + button (3) on
the front panel or remote control. To decrease the volume
level, press the VOL - button (4) on the front panel or remote
control.The volume ranges from "0" to "40". When the volume
level reaches "0" or "40", a triple beep sounds, indicating that
the adjustment limit has been reached. The screen displays
the volume level for 3 seconds.
Programmable Turn-On Volume
This feature allows the user to select a turn-on volume setting
regardless of the volume setting prior to turning the unit off.
To program a specific volume level, push and hold the
AUDIO button (2) while the yellow volume bar is displayed on
the screen. The unit will beep two times to confirm your turn-
on volume setting.
Audio Control Menu
The Audio Control feature allows you to easily adjust your
audio system to meet the acoustical characteristics of your
vehicle, which vary depending on the type of vehicle and its
measurements. To get the best possible sound quality from
your new system, be sure to adjust the settings for the
speakers as well. Proper setting of the Fader and Balance
boosts the effects of the cabin equalizer.
Accessing the Audio Control Menu
Press the AUDIO/LOC button (2) on the front panel to display
the "AUDIO" menu.
Selecting an Audio Feature for Adjustment
Press the (<)/(>) buttons (8, 9) on the joystick or the (|<<)/
(>>|) buttons (17, 19) on the remote control to select the
audio feature to be adjusted.
Adjusting an Audio Feature
Press the >> or << buttons (14, 22) on the remote control or
the /\ or V buttons (6, 7) on the joystick to adjust the selected
feature to the desired setting.
button (18) or the Table 5: Audio Adjustments
Audio Function
EQ
BASS
TREBL
SUB
LOUD
FAD (Fade)
BAL
NOTE: The Bass and Treble levels are only adjustable
when EQ is set to "User" mode.
The Loud function compensates for deficiencies in sound ranges at
low levels. Loudness levels range from 1-4 or "off". When the Loud
function is on, "LOUD" is displayed on the screen.
Exiting the Audio Control Menu
Press and hold the AUDIO/LOC button (2) or stop making
adjustments for a few seconds to exit the audio control menu.
Six-Channel Audio Control
NOTE: Before adjusting the volume of any speaker,
please refer to "Surround Sound" on page 25.
Master Volume
Front Left Channel Volume
Front Right Channel Volume
Rear Left Channel Volume
Rear Right Channel Volume
Center Channel Volume
Subwoofer Volume
Rear Zone
Adjustable Range If a monitor is installed in the rear zone and connected to the
rear zone AV output, passengers in the back seat can control
User
the DVD output using the rear zone remote control. See
Flat
"Multi-Zone Remote Control" on page 11 for instructions.
Jazz
System Reset
Pop
Classical To correct a system halt or other illegal
operation, use the tip of a pen to press the
Rock
RESET button (25) located on the front
Vocal
bottom-right corner of the unit. After a system reset, the unit restores
-14 to +14
all factory default settings.
-14 to +14
-7 to +7
NOTE: If the unit is reset while a DVD is playing, the DVD
0 (off), 1-4
resumes play once the reset is complete.
-9 to +9
-9 to +9
Line Mute
If the "MUTE" wire is connected, audio output mutes when a
telephone call is received by the car phone or when verbal
navigation is performed.
14
VM9021TS
Table 6: 6-Channel Audio Adjustments
Item Adjustable Range
00 to 40
-10 to +10
-10 to +10
-10 to +10
-10 to +10
-10 to +10
-10 to +10
[RESET] Button