Technical Information; Serial Number Location; Carburetor Modifications For High Altitude Operation; Emission Control System Information - Honda GX100 Manuel De L'utilisateur

TECHNICAL INFORMATION

Serial Number Location

Record the engine serial number, type and purchase date in the spaces
below. You will need this information when ordering parts and when
making technical or warranty inquiries.
ENGINE SERIAL NUMBER
ENGINE TYPE
Engine serial number: __ __ __ __ — __ __ __ __ __ __ __
Engine type: ___ ___ ___ ___
Date Purchased: ______ / ______ / ______

Carburetor Modifications for High Altitude Operation

At high altitude, the standard carburetor air-fuel mixture will be too rich.
Performance will decrease, and fuel consumption will increase. A very
rich mixture will also foul the spark plug and cause hard starting.
Operation at an altitude that differs from that at which this engine was
certified, for extended periods of time, may increase emissions.
High altitude performance can be improved by specific modifications to
the carburetor. If you always operate your engine at altitudes above
610 meters (2,000 feet), have your servicing dealer perform this
carburetor modification. This engine, when operated at high altitude
with the carburetor modifications for high altitude use, will meet each
emission standard throughout its useful life.
Even with carburetor modification, engine horsepower will decrease
about 3.5% for each 300 meter (1,000 foot) increase in altitude. The effect
of altitude on horsepower will be greater than this if no carburetor
modification is made.
When the carburetor has been modified for high altitude operation, the air-
fuel mixture will be too lean for low altitude use. Operation at altitudes below
610 meters (2,000 feet) with a modified carburetor may cause the engine to
overheat and result in serious engine damage. For use at low altitudes, have
your servicing dealer return the carburetor to original factory specifications.

EMISSION CONTROL SYSTEM INFORMATION

Source of Emissions

The combustion process produces carbon monoxide, oxides of nitrogen,
and hydrocarbons. Control of hydrocarbons and oxides of nitrogen is
very important because, under certain conditions, they react to form
photochemical smog when subjected to sunlight. Carbon monoxide
does not react in the same way, but it is toxic.
Honda utilizes appropriate air/fuel ratios and other emissions control
systems to reduce the emissions of carbon monoxide, oxides of nitrogen,
and hydrocarbons.
Additionally, Honda fuel systems utilize components and control
technologies to reduce evaporative emissions.
The U.S. and California Clean Air Acts, and Environment and Climate
Change Canada (ECCC)
U.S. EPA, California and Canadian regulations require all manufacturers to
furnish written instructions describing the operation and maintenance of
emission control systems.
The following instructions and procedures must be followed in order to
keep the emissions from your Honda engine within the emission
standards.

Tampering and Altering

Tampering is a violation of federal and California law.
Tampering with or altering the emission control system may increase
emissions beyond the legal limit. Among those acts that constitute
tampering are:
• Removal or alteration of any part of intake, fuel, or exhaust systems.
• Alterations that would cause the engine to operate outside its design
parameters.

Problems That May Affect Emissions

If you are aware of any of the following symptoms, have your engine
inspected and repaired by your authorized Honda Power Equipment
dealer.
• Hard starting or stalling after starting.
• Rough idle.
• Misfiring or backfiring under load.
• Afterburning (backfiring).
• Black exhaust smoke or high fuel consumption.

Replacement Parts

The emissions control systems on your new Honda engine were
designed, built, and certified to conform with EPA, California (models
certified for sale in California only), and Canadian emissions regulations.
We recommend the use of Honda Genuine parts whenever you have
maintenance done. These original design replacement parts are
manufactured to the same standards as the original parts, so you can be
confident of their performance. Honda cannot deny coverage under the
emission warranty solely for the use of non-Honda replacement parts or
service performed at a location other than an authorized Honda
dealership; you may use comparable EPA certified parts, and have service
performed at non-Honda locations. However, the use of replacement
parts that are not of the original design and quality may impair the
effectiveness of your emissions control system.
A manufacturer of an aftermarket part assumes the responsibility that
the part will not adversely affect emissions performance. The
manufacturer or rebuilder of the part must certify that use of the part will
not result in a failure of the engine to comply with emissions regulations.
ENGLISH
13