Olympus OEV143 Mode D'emploi page 2

English
WARNING
Please read and follow the warnings, cautions and notes
carefully. Ignoring these may result in injury to you or
damage to the product. This instruction manual describes
warnings, cautions and notes as well as how to use the
product safely. Please read the manual carefully and keep
it in an easily accessible location.
Owner's Record
The model and serial numbers are located at the rear.
Record these numbers in the spaces provided below.
Refer to these numbers whenever you call upon your
Olympus representative or the nearest Olympus service
center regarding this product.
Model No.
Serial No.
To prevent fire or shock hazard, do not expose the unit to
rain or moisture.
Dangerously high voltages are present inside the unit. Do
not open the cabinet. Refer servicing to qualified personnel
only.
In the event of a malfunction or when maintenance is
necessary, consult an authorized Olympus dealer.
This unit contains substances which can pollute the
environment if disposed carelessly. Please contact our
nearest representative office or your local environmental
office in case of disposal of this unit.
Power Switch
The power switch is a functional switch only.
To isolate the set from the mains supply remove the mains
plug from the wall socket.
FOR CUSTOMERS IN THE UNITED KINGDOM
WARNING
THIS APPARATUS MUST BE EARTHED
IMPORTANT
The wires in this mains lead are coloured in accordance
with the following code:
GREEN-AND-YELLOW— EARTH
BLUE — NEUTRAL
BROWN — LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
identifying the terminals in your plug PROCEED AS
FOLLOWS:
The wire coloured GREEN AND YELLOW must be
connected to the terminal on the plug marked with the letter
E or by the safety earth symbol Y or coloured GREEN or
GREEN-AND-YELLOW.
The wire coloured BROWN must be connected to the
terminal marked with the letter L or coloured RED.
The wire coloured BLUE must be connected to the terminal
marked with the letter N or coloured BLACK.
Ensure that your equipment is connected correctly — If you
are in any doubt consult a qualified electrician.
2
FOR THE CUSTOMERS IN THE USA
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residen-
tial area is likely to cause harmful interference in which case
the user will be required to correct the interference at his
own expense.
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority
to operate this equipment.
ATTENTION – When the product is installed in a
trolley:
a) Elevated operating ambient temperature
If installed in a closed or multi-unit trolley assembly, the
operating ambient temperature of the trolley environment
may be greater than room ambient.
Therefore, consideration should be given to installing the
equipment in an environment compatible with the
manufacturer's maximum rated ambient temperature of
0 to +40°C (Tmra).
b) Reduced air flow
Installation of the equipment in a trolley should be such
that the amount of air flow required for safe operation of
the equipment is not compromised.
c) Mechanical loading
Mounting of the equipment in the trolley should be such
that a hazardous condition is not achieved due to
uneven mechanical loading.
d) Circuit overloading
Condideration should be given to the connection of the
equipment to the supply circuit and the effect that
overloading of circuits might have on overcurrent
protection and supply wiring.
Appropriate consideration of equipment nameplate
ratings should be used when addressing this concern.
e) Reliable earthing
Reliable earthing of trolley-mounted equipment should
be maintained. Particular attention should be given to
supply connections other than direct connections to the
branch circuit (e.g., use of power strips).
Be sure to connect the AC power cord to a grounded
outlet.