Oil Change; Reduction Case Oil; Recommended Oil; Oil Level Check - Honda GX120 Manuel De L'utilisateur

4. Reinstall the oil filler cap/dipstick.
OIL FILLER CAP/DIPSTICK
OIL FILL HOLE
(bottom edge)
Running the engine with a low oil level can cause engine damage.
This type of damage is not covered by the Distributor's Limited
Warranty.
The Oil Alert system (applicable types) will automatically stop the
engine before the oil level falls below the safe limit. However, to
avoid the inconvenience of an unexpected shutdown, always check
the engine oil level before startup.

Oil Change

Drain the used oil when the engine is warm. Warm oil drains
quickly and completely.
1. Place a suitable container below the engine to catch the used oil,
then remove the oil filler cap/dipstick, oil drain plug and sealing
washer.
2. Allow the used oil to drain completely, then reinstall the oil drain
plug and a new sealing washer, and tighten the oil drain plug
securely.
TORQUE: 18 N∙m (13 lbf∙ft, 1.8 kgf∙m)
Please dispose of used motor oil in a manner that is compatible
with the environment. We suggest you take used oil in a sealed
container to your local recycling center or service station for
reclamation. Do not throw it in the trash, pour it on the ground,
or pour it down a drain.
3. With the engine in a level position, fill with the recommended oil
(see page 8) to the upper limit mark (bottom edge of the oil fill
hole) on the dipstick.
Engine oil capacity: GX120: 0.56 L (18 US oz, 0.49 lmp qt)
GX160: 0.58 L (19 US oz, 0.51 lmp qt)
GX200: 0.6 L (20 US qt, 0.53 lmp qt)
Running the engine with a low oil level can cause engine
damage. This type of damage is not covered by the
Distributor's Limited Warranty.
The Oil Alert system (applicable types) will automatically stop
the engine before the oil level falls below the safe limit.
However, to avoid the inconvenience of an unexpected
shutdown, fill to the upper limit, and check the oil level
regularly.
4. Install the oil filler cap/dipstick and tighten securely.
UPPER LIMIT
LOWER LIMIT
Wash your hands with soap and water after handling used oil.
REDUCTION CASE OIL (applicable types)

Recommended Oil

Use the same oil that is recommended for the engine (see page 8).

Oil Level Check

Check the reduction case oil level with the engine stopped and in a
level position.
2 : 1 Reduction Case With Centrifugal Clutch
1. Remove the oil filler cap/dipstick and wipe it clean.
2. Insert and remove the oil filler cap/dipstick without screwing it
into the filler hole. Check the oil level shown on the oil filler cap/
dipstick.
3. If the oil level is low, add the recommended oil to reach the
upper limit mark on the dipstick.
4. Screw in the oil filler cap/dipstick and tighten securely.
UPPER
LIMIT
6 : 1 Reduction Case
1. Remove the oil-level-check bolt
and washer, and see whether
the oil level is at the edge of the
bolt hole.
2. If the oil level is below the check
bolt hole, remove the filler bolt
and washer. Add oil until it
starts to flow out the check bolt
hole with the recommended oil
(see page 8).
3. Install the oil-level-check bolt,
filler bolt and new washers.
Tighten them securely.
ENGLISH
SEALING WASHER (Replace)
DRAIN PLUG
OIL FILLER CAP/
DIPSTICK
OIL LEVEL
LOWER LIMIT
OIL FILLER CAP/DIPSTICK
FILLER BOLT
OIL LEVEL
OIL-LEVEL-CHECK BOLT
9