Bosch GSC 75-16 Professional Notice Originale page 11

d Cutter clearance a
max
(mm) (mm)
0.3−0.6 0.10
0.8−1.2 0.25
1.3−1.6 0.30
For softer or more ductile materials, the clearance a must be
decreased; for harder or more brittle materials, it must be in-
creased.
Loosen the fastening screw (8) for the bottom cutter. Adjust
the requested cutter clearance a with the set screw (7) for
the bottom cutter. The upper cutter (5) and the bottom cut-
ter (6) may not touch each other.
Check the clearance with a commercially available setting
gauge. Retighten the fastening screw (8) for the bottom cut-
ter with a tightening torque of 4–6 Nm.
Maintenance and Service
Maintenance and Cleaning
Pull the plug out of the socket before carrying out any
u
work on the power tool.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.
In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by an
after-sales service centre that is authorised to repair Bosch
power tools.
Changing the cutter (see figure A)
The upper cutter (5) and the bottom cutter (6) are identical,
have four cutting edges each, and can be exchanged with
each other.
Turn or replace the cutters in good time. Only sharp applica-
tion tools achieve good cutting capacity and make the power
tool last longer.
To replace the upper cutter (5) loosen the fastening
screw (4), to replace the bottom cutter (6) loosen the
fastening screw (8).
Turn the cutter by 90° or install a new cutter. When installing
the bottom cutter (6), ensure that it fits against the set
screw (7).
Note: Turn the cutter only in the direction indicated in the
figure A and only insert a new cutter in the position shown in
the figure. Cutting is not possible with an incorrectly inser-
ted cutter.
Retighten the fastening screw (4) for the upper cutter and
the fastening screw (8) for the bottom cutter with a tighten-
ing torque of 4–6 Nm. Check the cutter clearance a as de-
scribed above.
Upper cutter (5) and bottom cutter (6) may not be re-
ground.
After-Sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
Bosch Power Tools
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch-pt.com.au
www.bosch-pt.co.nz
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
KZN – BSC Service Centre
Unit E, Almar Centre
143 Crompton Street
Pinetown
Tel.: (031) 7012120
English | 11
1 609 92A 50F | (27.06.2019)