Operation - EINHELL GE-CC 18 Li Instructions D'origine

5.2 Height adjustment (Fig. 7)
Undo the union nut (Fig. 7/Item 5) until the paving
scraper's handle can be moved in and out freely.
Now set the required working height and secure
the handle in this position by tightening the union
nut again.
5.3 Adjusting the additional handle (Fig. 8)
Undo the adjustment lock (Fig. 8/Item 3) for the
additional handle until it can be moved forwards
and backwards without any great resistance. Set
the required position and tighten the securing
screw again.
5.4. Installing the battery (Fig. 9/10)
Press the side pushlock button of the battery
pack as shown in Fig. 9 and push the battery
pack into the mount provided. When the battery
is positioned as in Fig. 10, make sure that the
pushlock button latches in place! To remove the
battery pack, proceed in reverse order.
5.5 Charging the battery (Fig. 11)
1. Take the battery pack out of the equipment.
Do this by pressing the side pushlock buttons.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(14) into the socket outlet. The green LED will
then begin to fl ash.
3. Insert the battery pack (13) into the battery
charger (14).
4. In the section entitled „Charger indicator" you
will fi nd a table with an explanation of the LED
indicator on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts.
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless paving
scraper drops. Never allow the battery pack to
become fully discharged. This will cause it to de-
Anl_GE_CC_18_Li_SPK7.indb 19 Anl_GE_CC_18_Li_SPK7.indb 19
GB
velop a defect.
5.6 Battery capacity indicator (Fig. 11b)
Press the switch for the battery capacity indicator
(Fig. 11b/Item A). The battery capacity indicator
(Fig. 11b/Item B) shows the charge status of the
battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs fl ash:
The battery pack has undergone exhaustive di-
scharge and is defective. Do not use or charge a
defective battery pack!

6. Operation

To obtain maximum performance from your pa-
ving scraper, please follow the instructions given
below:
•
Never use the paving scraper without the gu-
ard.
•
To switch on your paving scraper press the
safety lock-off (Fig. 2/Item 1) and then press
the On/Off switch (Fig. 2/Item 2).
•
To switch off your paving scraper, let go of the
On/Off switch again (Fig. 2/Item 2).
One steel brush (Fig. 2/Item 9) and one nylon
brush (Fig 2/Item 8) are supplied with the equip-
ment. The wire brush is suited for use on robust
surfaces and obstinate weeds. We recommend
using the nylon brush for light vegetation and sur-
faces too sensitive for the steel brush.
Important! Always carry out a short trial run
to check out possible eff ects on the surfaces
of the paving stones or slabs before starting
with your work. Never use the equipment on
very sensitive surfaces, for example tiles.
Important! Only use brushes which are in
fl awless condition. Replace excessively worn
or damaged brushes immediately.
- 19 -
25.08.2016 14:59:45 25.08.2016 14:59:45