Table des Matières
Publicité
•
the model
•
the serial number and/or INVENTORY number
•
the date of purchase/production
•
the date of the first use
•
the next inspection
•
remarks
•
the examiner's name and signature or his initials
Please refer to the following notes on regular inspection and the assessment of safe use:
•
2) Regulations for the owner of the equipment
A.HABERKORN safety products must be inspected on the following points before each use:
•
2.2 Care, storage and transport of the PPE against falls from a height
•
3) Period of use
Labels or markings must not be removed from the product in order to always guarantee the traceability of the product.
2.2 Care, storage and transport of the PPE against falls from a height
This product can be cleaned dry or damp with a soft brush. Webbings and ropes can also be cleaned with lukewarm
water (max. 40° C) and mild soapsuds by hand. Then rinse in cold water and let it dry in a well ventilated, dry and
shady place (avoid UV light exposure) (never tumble dry or dry over a direct source of heat). Please take care that
the marking labels remain legible after cleaning. This product must be stored under dry conditions, at an ambient
temperature, protected from mechanic damage, chemical influences (e.g. of chemical substances, oil, solvents and other
aggressive substances), direct sunlight (UV light exposure) and outside a transport container. We recommend transporting the
device in a UV resistant bag and not exposing it more than necessary to UV rays by direct sunlight.
2.3 Repair/Accessories
Eventual repair, modification or additions to the PPE generally have to be carried out exclusively by the manufacturer.
2.4 Training/Instructions
Personal protective equipment against falls from a height must only be used by persons, who have been instructed according to the
valid national working conditions act. We are pleased to inform you about training for INSTRUCTIONS or COMPETENT
PERSONS.
3 Period of use
The operating life of this safety product essentially depends on the type and frequency of use as well as on the conditions of use,
diligent care and storage and therefore can not generally be defined. Products made of chemical fibres (e.g.: polyamid, polyester,
aramid) are subject to certain ageing even if they are not used, especially depending on the intensity of ultraviolet rays as well as on
the climatic environmental influences.
Maximum longevity of 12 years
The maximum longevity of A.HABERKORN products in synthetic and textile material is 12 years from the date of production under
optimal storage conditions and without being used.
Maximum operating life of 10 years
The maximum operating life with occasional, proper use without visible wear and tear under optimal storage conditions is 10 years
from the date of first use.
Storage period of 2 years
The storage period before first use and without reducing the maximum operating life is 2 years from the date of production.
Provided that all instructions on safe handling and storage are observed, the following, non-binding indications on the lifespan
can be recommended:
•
Intensive, daily use
•
Regular use throughout the year
•
Regular seasonal use
•
Occasional use (once a month)
•
Sporadic use
Metal fittings such as buckles, karabiners, etc.:
The life of metal fittings is generally unlimited; however, a periodic inspection of metal fittings must be carried out regarding
damage, distortion and wear as well as functioning.
When different materials are used in one product, the period of use is subject to the most sensitive materials.
Extreme conditions of use can cause the elimination of a product after only using once (type and intensity of use, field of
application, aggressive environment, sharp edges, extreme temperatures, chemical substances etc.).
A PFPE must definitely be discarded:
• in case of damage to supporting parts, which are essential for safety, such as webbings and seams (tears, cuts or other)
• in case of damage to plastic and/or metal fittings
• in case of strain by a fall or heavy load
• after the application period has elapsed
• if a product does not seem safe or reliable anymore
• if the product is outdated and does not comply with the technical standards anymore (modification of legal regulations,
norms and technical rules, incompatibility with other equipment etc.)
• if the history of use is unknown or incomplete (test manual)
• if the identification of the product does not exist or if it is illegible or missing (even partly)
• if the instructions for use/test manual of the product are missing (because product history can not be tracked!)
• See also item: 2) Regulations for the owner of the equipment
If the visual inspection carried out by the user, holder of the equipment or the competent person results in complaint or if the PPE
has elapsed, it has to be discarded. The elimination has to be made in such a way that reuse in action can absolutely be excluded
(e.g. by cutting and disposing of belts, fittings etc.). In case of frequent use, intensive wear or extreme environmental influences,
the allowed period of use becomes shorter. The decision on the operational capability of the device is up to the responsible
COMPETENT PERSON within the prescribed periodic inspection.
4 Liability (complementing point Caution)
- less than 1 year
- 1 year to 2 years
- 2 to 3 years
- 3 to 4 years
- 5 to 7 years
9
Publicité
Table des Matières
