Care, Storage And Transport Of The Ppe Against Falls From A Height; Repair/Accessories; Training/Instructions; Period Of Use - A.HABERKORN Longue de sauvetage Mode D'emploi

The result of this visual inspection has to be entered into the test sheet (last page!). The next test date must be marked by the
tester
on the product label.
2.2

Care, storage and transport of the PPE against falls from a height

This product can be cleaned dry or damp with a soft brush. Webbings and ropes can also be cleaned with lukewarm
water (max. 40° C) and mild soapsuds by hand. Then rinse in cold water and let it dry in a well ventilated, dry and
shady place (avoid UV light exposure) (never tumble dry or dry over a direct source of heat). Please take care that
the marking labels remain legible after cleaning. This product must be stored under dry conditions, at an ambient
temperature, protected from mechanic damage, chemical influences (e.g. of chemical substances, oil, solvents and
other aggressive substances), direct sunlight (UV light exposure) and outside a transport container. We recommend transporting
the device in a UV resistant bag and not exposing it more than necessary to UV rays by direct sunlight.
2.3

Repair/Accessories

Eventual repair, modification or additions to the PPE generally have to be carried out exclusively by the manufacturer.
2.4

Training/Instructions

Personal protective equipment against falls from a height must only be used by persons, who have been instructed according to the
valid national working conditions act.
We are pleased to inform you about training for INSTRUCTIONS or COMPETENT PERSONS.

3 Period of use

The operating life of this safety product essentially depends on the type and frequency of use as well as on the conditions of use,
diligent care and storage and therefore cannot generally be defined. Products made of chemical fibres (e.g.: polyamide, polyester,
aramid) are subject to certain ageing even if they are not used, especially depending on the intensity of ultraviolet rays as well as on
the climatic environmental influences.
Maximum longevity of 12 years
The maximum longevity of A.HABERKORN products in synthetic and textile material is 12 years from the date of production under
optimal storage conditions and without being used.
Maximum operating life of 10 years
The maximum operating life with occasional, proper use without visible wear and tear under optimal storage conditions is 10 years
from the date of first use.
Storage period of 2 years
The storage period before first use and without reducing the maximum operating life is 2 years from the date of production.
Provided that all instructions on safe handling and storage are observed, the following, non-binding indications on the lifespan
can be recommended:

Intensive, daily use

Regular use throughout the year

Regular seasonal use

Occasional use (once a month)

Sporadic use
Work positioning belts, full body harnesses, sit harnesses:
With normal use in compliance with instructions for use, the realistic period of use for full body harnesses is 6 to 8 years. When
properly stored and without being used: 10 years.
Based on: BGR 198 – German trade association rules for safety and health at work (BG rules) / DE.
Metal fittings such as buckles, karabiners, etc.:
The life of metal fittings is generally unlimited; however, a periodic inspection of metal fittings must be carried out regarding
damage, distortion and wear as well as functioning.
When different materials are used in one product, the period of use is subject to the most sensitive materials.
Extreme conditions of use can cause the elimination of a product after only using once (type and intensity of use, field of
application, aggressive environment, sharp edges, extreme temperatures, chemical substances etc.).
A PFPE must definitely be discarded:
 in case of damage to supporting parts, which are essential for safety, such as webbings and seams (tears, cuts or other)
 in case of damage to plastic and/or metal fittings
 in case of strain by a fall or heavy load
 after the application period has elapsed
 if a product does not seem safe or reliable anymore
 if the product is outdated and does not comply with the technical standards anymore (modification of legal regulations,
norms and technical rules, incompatibility with other equipment etc.)
 if the history of use is unknown or incomplete (test manual)
 if the identification of the product does not exist or if it is illegible or missing (even partly)
 if the instructions for use/test manual of the product are missing (because product history cannot be tracked!)
 See also item: 2) Regulations for the owner of the equipment
If the visual inspection carried out by the user, holder of the equipment or the competent person results in complaint or if the PPE
has elapsed, it has to be discarded. The elimination has to be made in such a way that reuse in action can absolutely be excluded
(e.g. by cutting and disposing of belts, fittings etc.).
In case of frequent use, intensive wear or extreme environmental influences, the allowed period of use becomes shorter. The
decision on the operational capability of the device is up to the responsible COMPETENT PERSON within the prescribed periodic
inspection.
- less than 1 year
- 1 year to 2 years
- 2 to 3 years
- 3 to 4 years
- 5 to 7 years
5