EINHELL BT-PO 1100/2 E Mode D'emploi D'origine page 13

Anleitung_BT_PO_1100_2_E_SPK1__ 16.10.14 15:02 Seite 13
Before you start the equipment, check to ensure
n
that the attachments are securely installed.
Never touch the area you wish to polish with the
n
edge of the sanding/grinding disk.
Use the speed selector (Fig. 3/Item 4) to select the
n
following maximum speeds for polishing:
- Working in polish:
- Polishing to a high gloss: approx. 1000-1100 rpm
- Polishing up:
If you do not comply with these instructions, the
manufacturer cannot accept any liability.
The Velcro fastener enables easy changing of the
polishing attachment.
- Use the foamed plastic attachment to apply the
polishing agent (Fig. 7).
Make sure that the foamed plastic attachment is
n
free of any foreign bodies.
Spread the polishing paste evenly over the
n
polishing pad. Do not apply the polish directly to
the polishing surface.
Switch the polishing machine on and off only
n
when the polishing machine is resting on the
polishing surface.
Place the extension lead over your shoulder and
n
work first on the large, flat surfaces such as the
bonnet, boot lid and roof.
Keep your movements as regular as possible.
n
Important! Allow the polishing machine to glide
n
over the polishing surface. Do not exert pressure!
Work next on the smaller surfaces (doors, for
n
example)
- Use the fleece attachment to finish off the polishing
(Fig. 8).
Make sure that the fleece attachment is free of all
n
foreign bodies.
Remove the layer of polish in the same order as it
n
was applied.
Important! Do not exert pressure on the
n
polishing machine!
Care tips
For optimum paintwork protection, you should
n
polish your car 2 to 3 times a year.
Wash your car at least every 2 weeks. Avoid
n
using household detergents as these can damage
the paintwork and remove the layer of wax.
Wash your car with a clean sponge, working from
n
top to bottom.
Remove all insects, bird droppings and tar stains
n
from the paintwork daily.
If you use any window-cleaning agents, spray
n
them onto a cloth and not directly onto the
windows in order to prevent them wetting the
paintwork.
7.3 Using as a sanding machine
Use the supplied sanding attachments (Fig. 9) for
sanding purposes.
The Velcro fastener enables easy changing of the
sanding attachments.
approx. 1000 rpm
Place the whole surface area of the sanding disk
n
on the material.
approx. 1400 rpm
Switch on the machine and move it with gentle
n
pressure over the workpiece completely circular
movements or moving it to and fro and up and
down.
Use a coarse paper for coarse sanding and a
n
finer paper for finish sanding. You can find the
best paper for the job by means of testing.
7.4 Speed Control (Fig. 3)
Use the speed control to set the desired working
speed.
Press the "+" button to increase the speed.
Press the "-" button to decrease the speed.
Refer to the display (8) for the set speed.
Set speed = Display x 100
8. Replacing the power cable
Danger!
If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
9. Cleaning, maintenance and ordering
of spare parts
Danger!
Always pull out the mains power plug before starting
any cleaning work.
9.1 Cleaning
Keep all safety devices, air vents and the motor
n
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
n
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
n
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.
Wash the polishing attachments only by hand and
n
GB
13