System Setup; System Setup Operation; Setting The External Device Interrupt Mode; Setting The Interrupt Icon Display - Alpine IVA-W203 Mode D'emploi

SYSTEM Setup

System Setup Operation

To display the System mode screen:
To watch a video source, your vehicle must be parked with the
ignition key in the ACC or ON position. To do this, follow the
procedure below.
1 Bring your vehicle to a complete stop at a safe
location. Engage the parking brake.
2 Keep pushing the foot brake and release the parking
brake once then engage it again.
3 When the parking brake is engaged for the second
time, release the foot brake.
• For automatic transmission vehicles, place the transmission lever
in the Park position.
Now, the locking system for the System mode operation has been
released. Engaging the parking brake can reactivate the System
mode, as long as the car's ignition has not been turned off. It is
not necessary to repeat the above procedure (1 through 3) of "To
display the System mode screen."
Each time the ignition is turned OFF, perform the procedure of "To
display the System mode screen."
The following steps 1 to 4 are common operations to each
"Setting item" of SYSTEM Setup. Refer to each section for
details.
1
Touch [SETUP] on the main source screen.
The SETUP selection screen is displayed.
2
Touch [SYSTEM].
The SYSTEM SETUP screen appears.
3
Touch [ ], [ ] or [OFF], [ON], etc., of the desired
item to change its setting.
Setting items:
IN INT. MUTE / IN INT. ICON / REMOTE SENSOR
CAMERA IN / NAV. MIX / AUX IN / AUX IN LEVEL
BLUETOOTH IN / USB ADAPTER / VISUAL KEY /
CUSTOMISE KEY / OPTICAL OUT / SUBWOOFER
*1
Not displayed when OFF is set in "Setting the AUX Mode"
(page 36).
*2
Not displayed when an external audio processor is connected.
*3
When ON is set in "Setting the Picture Output" (page 36), the item is
displayed.
4
Touch [RETURN] to return to the previous screen.
Touch and hold [RETURN] for at least 2 seconds to return to
the main source screen that was displayed before the setup
operation was started.
• Immediately after changing the settings of System Mode (while the
system is writing data automatically) do not turn the ignition key
(engine key) to OFF. Otherwise, the settings may not be changed.

Setting the External Device Interrupt Mode

If an Alpine Ai-NET Auxiliary Input Adapter (KCA-801B) is
connected to the IVA-W203, an Auxiliary Source will be allowed to
interrupt the current audio source. For example, you can listen to a
portable MP3 player through your car audio system even with a CD
changer connected and playing. The CD changer will automatically
mute when switched to the AUX Input. For further details on how to use
the Alpine KCA-801B, see your authorized Alpine dealer.
Setting item: IN INT. MUTE
Setting contents: OFF / ON
OFF: The volume level can be adjusted in Interrupt mode.
ON:
• The auxiliary device being connected must have an Interrupt wire
with a negative trigger for this function to operate automatically.
Otherwise, a separate switch needs to be added to switch it manually.

Setting the Interrupt Icon Display

The unit can display the icon of an external device, such as a telephone,
whenever a phone call comes in to tell you there is a phone call.
Setting item: IN INT. ICON
Setting contents: INT / TEL
INT:
TEL: When the external device (telephone) sends the interrupt
Switching the function of the remote
sensor
For remote control operation, the remote sensor of the external device
(monitor, etc.) can be switched, as you prefer.
Setting item: REMOTE SENSOR
Setting contents: FRONT / REAR
FRONT:
REAR:
*3
/
*1
/ AUX OUT /
• The touch panel rear monitor sensor has priority over the remote
control sensor. If the rear monitor (connected to the Alpine rear
*2
monitor output via the Monitor control lead) is touched, the
command is executed regardless of the remote control sensor switch
setting. Note, however, that the remote control sensor that has been
set takes priority if it has been 5 seconds since last touching the
panel.
• When an optional DVD changer or DVD player is connected, and the
remote control sensor is set to REAR, some soft button operations
( [ ] STOP, etc.) cannot be performed. In this case, set the remote
control sensor to FRONT.
Sound will not be output. The icon that is set in "Setting
the Interrupt Icon Display" is displayed.
The INT icon appears on the display.
signal, the telephone icon appears on the display.
The remote sensor of this unit is effective.
The remote sensor of the external monitor
connected to AUX OUT of this unit becomes
effective. The remote control operates the
source connected to the AUX OUT terminals.
35
-EN