Publicité
Les langues disponibles
Les langues disponibles
EN
After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power
tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.
Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear
•
dust mask, hearing protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protec-
tion must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtrating particles
generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.
Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Frag-
•
ments of workpiece or of a broken accessory may fly away and cause injury beyond immediate area of operation.
Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into
•
the spinning accessory.
Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the
•
power tool out of your control.
Regularly clean the power tool's air vents. The motor's fan will draw the dust inside the housing and excessive accumulation of powdered metal
•
may cause electrical hazards.
•
Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.
Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the
•
accessory into your body.
Do not operate the power tool near flammable materials. Sparks could ignite these materials.
•
•
Use auxiliary handles when supplied with the tool. Loss of control can cause personal injury.
When a suspension device is used, ensure that it is securely fastened. Failure to secure may result in loss of control, unexpected motion, or
•
dropping of the tool.
Keep clear of pinch point between reaction bar or support handles and any fixed object in work area. Pinching or other injury may occur.
•
•
Exposed throttles shall not be used where obstructions can hold the throttle in the "on" position. You may not be able to turn the tool off.
Kickback and Related Warnings
•
Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle,
if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback
forces, if proper precautions are taken.
•
Never place your hand near the rotating accessory. Accessory may kickback over your hand.
Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to
•
the wheel's movement at the point of snagging.
Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing
•
have a tendency to snag the rotating accessory and cause loss of control or kickback.
Do not attach saw chain wood carving blade or toothed saw blade. Such blades create frequent kickback and loss of control.
•
Additional safety instructions for sanding operations
Do not use excessively oversized sanding disc paper. Follow manufacturers recommendations, when selecting sanding paper. Larger
•
sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback.
Additional safety instructions for polishing operations
Do not allow any loose portion of the polishing bonnet or its attachment strings to spin freely. Tuck away or trim any loose attachment
•
strings. Loose and spinning attachment strings can entangle your fingers or snag on the workpiece.
Accessory hazards
•
The abrasive disc shall be located centrally on the pad with adhesive or lock device as required and intended.
•
Accessory manufacturers' safety precautions and warnings, operating restrictions, and installation or mounting instructions shall be followed, un-
less it contradicts information provided in this manual or other literature provided with the tool. For contradictory information follow whichever is
the most restrictive guideline.
Product Safety Information: Battery
Product Description
A Battery is an electric energy storage device used as the power source for Ingersoll Rand Cordless Products.
General Battery Safety Warnings
•
Warning! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or
serious injury.
•
Save all warnings and instructions for future reference.
It is your responsibility to make this safety information available to others that will operate this product. Failure to follow standards and
•
regulations can cause personal injury.
Always install, operate, inspect and maintain this product in accordance with all applicable standards and regulations (local, state, coun-
•
try, federal, etc.). Compliance is your responsibility. Failure to follow standards and regulations can cause personal injury.
•
The term "power tool" in the warnings refers to your battery-operated (cordless) power tool.
Electrical Safety
•
Do not expose batteries or power tools to rain or wet conditions. Water entering a battery or power tool will increase the risk of electric shock.
Personal Safety
Do not modify this product, safety devices, or accessories. Unauthorized modifications may result in electric shock, fire or personal injury.
•
Battery and Power Tool Use and Care
Store idle batteries and power tools out of the reach of children and do not allow persons unfamiliar with the battery or power tool or these
•
instructions to operate the battery or power tool. Batteries and power tools are dangerous in the hands of untrained users.
Use the battery, power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working condi-
•
tions and the work to be performed. Use of the battery or power tool for operations different from those intended could result in a hazardous
EN-3
WARNING
47540127001_ed2
Publicité
