VONROC S CD501DC Traduction De La Notice Originale page 5

b) Hold power tool by insulated gripping surfaces
when. performing an operation where the cutting
accessory or fastener may contact hidden wiring.
Cutting accessory and fasteners contacting a
"live" wire may make exposed metal parts of
the power tool "live" and could give the opera-
tor an electric shock.
c) Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
d) Use appropriate detectors to determine if utility
lines are hidden in the work area or call the
local utility company for assistance. Contact
with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property
damage.
e) Switch off the power tool immediately when the
tool insert jams. Be prepared for high reaction
torque that can cause kickback. The tool insert
jams when:
- the power tool is subject to overload or;
- it becomes wedged in the workpiece.
f) Hold the machine with a firm grip. High reaction
torque can briefly occur while driving in and
loosening screws.
g) Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.
h) Always wait until the machine has come to a
complete stop before placing it down. The tool
insert can jam and lead to loss of control over
the power tool.
SAFETY WARNINGS FOR BATTERY
a) Do not open the battery. Danger of short-
circuiting.
b) Protect the battery against heat, e. g., against
continuous intense sunlight, fire, water, and
moisture. Danger of explosion.
c) In case of damage and improper use of the bat-
tery, vapours may be emitted. Ventilate the area
and seek medical help in case of complaints.
The vapours can irritate the respiratory system.
d) Use the battery only in conjunction with your
Vonroc product. This measure alone protects
the battery against dangerous overload.
e) The battery can be damaged by pointed objects
such as nails or screwdrivers or by force
applied externally. An internal short circuit can
occur and the battery can burn, smoke, explode
or overheat.
WWW.VONROC.COM
SAFETY WARNINGS FOR CHARGER
Intended use
Charge only CD801AA and CD803AA type rechargea-
ble Battery packs with the charger. Other types of bat-
teries may burst causing personal injury and damage.
a) The appliance is not to be used by persons
(including children) with reduced physical, sen-
sory or mental capabilities, or lack of experien-
ce and knowledge, unless they have been given
supervision or instruction.
b) Children being supervised not to play with the
appliance.
c) Do not recharging non-rechargeable batteries!
d) During charging, batteries must be placed in
the well ventilated area!
Electrical safety
Always check that the voltage of the power
supply corresponds to the voltage on the
rating plate.
• Do not use the machine if the mains cable or
the mains plug is damaged.
• Only use extension cables that are suitable
for the power rating of the machine with a
minimum thickness of 1.5 mm2. If you use a ex-
tension cable reel, always fully unroll the cable.
2. MACHINE INFORMATION
Intended use
This cordless drill is intended for driving in and
loosening screws as well as for drilling in wood,
metal and plastic.
TECHNICAL SPECIFICATIONS
Model No.
Voltage
Chuck capacity
Torque settings
No load speed
Position 1:
Position 2:
Weight
Sound pressure level L
PA
Sound power level L
WA
Hand-arm vibration a
h
(screwdriving without impact)
EN
S_CD501DC
20V
13 mm
21+ Drill mode
0-400 /min
0-1500 /min
1.15 kg
89.9 dB(A), K=3dB(A)
99.9 dB(A), K=3dB(A)
0.700 m/s K=1.5 m/s
2 2
5