Test Run - Toshiba Carrier MMD-AP0304H2UL Manuel D'installation

Filter sign setting
According to the installation condition, the filter sign
term (Notification of filter cleaning) can be changed.
Follow to the basic operation procedure
1 2 3 4 5 6
→ → → → →
( ).
3
• For the CODE No. in Procedure , specify [01].
4
• For the [SET DATA] in Procedure , select the SET
DATA of filter sign term from the following table.
SET DATA Filter sign term
0000 None
0001 150 H
2500 H
0002
(Factory default)
0003 5000 H
0004 10000 H
To secure better effect of
heating
When it is difficult to obtain satisfactory heating due to
installation place of the indoor unit or structure of the
room, the detection temperature of heating can be
raised. Also use a circulator or other machinery to
circulate heat air near the ceiling.
Follow to the basic operation procedure
1 2 3 4 5 6
→ → → → →
( ).
3
• For the CODE No. in Procedure , specify [06].
4
• For the set data in Procedure , select the SET
DATA of shift value of detection temperature to be
set up from the following table.
SET DATA Detection temperature shift value
0000 No shift
0001 1.8 °F (+1 °C)
3.6 °F (+2 °C)
0002
(Factory default)
0003 5.4 °F (+3 °C)
0004 7.2 °F (+4 °C)
0005 9.0 °F (+5 °C)
0006 10.8 °F (+6 °C)
25-EN
Remote control sensor
The temperature sensor of the indoor unit senses room
temperature usually. Set the remote control sensor to
sense the temperature around the remote control.
Select items following the basic operation procedure
1 2 3 4 5 6
→ → → → →
( ).
3
• Specify [32] for the CODE No. in Procedure .
• Select the following data for the SET DATA in
4
Procedure .
SET DATA 0000 0001
remote control Not used
Used
sensor (Factory default)
When flashes, the remote control sensor is
defective.
Select the SET DATA [0000] (not used) or replace the
remote control.
Group control
In a group control, a remote control can control up to
maximum 8 units.
• The wired remote control only can control a group
control. The wireless remote control is unavailable
for this control.
• For wiring procedure and wires of the individual line
(Identical refrigerant line) system, refer to "Electrical
connection" in this Manual.
• Wiring between indoor units in a group is performed
in the following procedure.
• Connect the indoor units by connecting the remote
control wires from the remote control terminal blocks
(A, B) of the indoor unit connected with a remote
control to the remote control terminal blocks (A, B) of
the other indoor unit. (Non-polarity)
• For address setup, refer to the Installation Manual
attached to the outdoor unit.
– 13 –
10

Test run

Before test run
• Before turning on the power supply, carry out the
following procedure.
1) By using 500 V-megger, check that resistance
of 1 MΩ or more exists between the terminal
block L to L and the earth (grounding).
1 2
If resistance of less than 1 MΩ is detected, do
not run the unit.
2) Check the valve of the outdoor unit being
opened fully.
• To protect the compressor at activation time, leave
power-ON for 12 hours or more before operating.
• Do not press the electromagnetic contactor to
forcibly perform a test run. (This is very dangerous
because the protective device does not work.)
• Before starting a test run, set addresses by following
the Installation Manual supplied with the outdoor
unit.
Execute a test run
Operate the unit with the wired remote control as usual.
For the procedure of the operation, refer to the
attached Owner's Manual to the outdoor unit.
A forced test run can be executed in the following
procedure even if the operation stops by thermostat-
OFF.
In order to prevent a serial operation, the forced test
run is released after 60 minutes have passed and
returns to the usual operation.
CAUTION
Do not use the forced test run for cases other than the
test run because it applies an excessive load to the
devices.
Wired remote control
2, 4
3
1,5
1
Push button for 4 seconds or more.
[TEST] is displayed on the display part and
the selection of mode in the test mode is
permitted.
2
Push button.
3
Select the operation mode with
button, [ Cool] or [ Heat].
• Do not run the air conditioner in a mode other
than [ Cool] or [ Heat].
• The temperature controlling function does not
work during test run.
• The detection of error is performed as usual.
4
After the test run, push button to
stop a test run.
1
(Display part is same as procedure .)
5
Push button to cancel (release from) the
test run mode.
([TEST] disappears on the display and the status
returns to a normal.)
26-EN