Bosch GKS 18 V-LI Professional Notice Originale page 16

OBJ_BUCH-755-005.book Page 17 Tuesday, February 3, 2015 11:32 AM
Technical Data
Circular Saw
Article number
Rated voltage
No-load speed
Cutting depth, max.
– for 0° bevel angle
– for 45° bevel angle
Spindle lock
Base plate dimensions
Saw blade diameter, max.
Saw blade diameter, min.
Blade thickness, max.
Tooth thickness/setting, max.
Tooth thickness/setting, min.
Mounting bore
Weight according to
EPTA-Procedure 01/2003
Permitted ambient temperature
– during charging
**
– during operation and during
storage
Recommended batteries
Recommended chargers
* depending on the battery pack being used
** Limited performance at temperatures <0 °C
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-5.
Typically the A-weighted noise levels of the product are:
Sound pressure level 95 dB(A); Sound power level
106 dB(A). Uncertainty K =3.0 dB.
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60745-2-5:
2
Cutting wood: a =3 m/s , K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Bosch Power Tools
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
GKS 18 V-LI
accessories, keep the hands warm, organisation of work pat-
3 601 F6H 0..
terns.
V= 18
Declaration of Conformity
-1
min 3900
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
mm 51
vant provisions of the directives 2011/65/EU, until
mm 40
19 April 2016: 2004/108/EC, from 20 April 2016 on:
 2014/30/EU, 2006/42/EC including their amendments and
complies with the following standards: EN 60745-1,
mm 146 x 272
EN 60745-2-5.
mm 165
Technical file (2006/42/EC) at:
mm 160
Robert Bosch GmbH, PT/ETM9,
mm 1.7
70764 Leinfelden-Echterdingen, GERMANY
mm 2.6
Henk Becker
Executive Vice President
mm 2.0
Engineering
mm 20
kg 3.9/4.1*
Robert Bosch GmbH, Power Tools Division
°C 0...+45
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 03.02.2015
°C –20...+50
GBA 18 V ...
Assembly
AL 18..
GAL 3680 Battery Charging
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
2
.
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
Observe the notes for disposal.
Removing the battery
The battery 3 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 24 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
To remove the battery 3, press the battery unlocking button
24 and pull the battery out of the power tool toward the rear.
Do not exert any force.
English | 17
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 14R | (3.2.15)