Dremel 200 Série Traduction De La Notice Originale page 21

control over kickback or torque reaction during start-up.
The operator can control torque reactions or kickback forces,
if proper precautions are taken.
b. Never place your hand near the rotating accessory.
Accessory may kickback over your hand.
c. Do not position your body in the area where power tool
will move if kickback occurs. Kickback will propel the tool
in direction opposite to the wheel's movement at the point of
snagging.
d. Use special care when working corners, sharp edges
etc. Avoid bouncing and snagging the accessory.
Corners, sharp edges or bouncing have a tendency to snag
the rotating accessory and cause loss of control or kickback.
e. Do not attach a saw chain woodcarving blade or toothed
saw blade. Such blades create frequent kickback and loss
of control.
SAFETY WARNINGS SPECIFIC FOR GRINDING
AND ABRASIVE CUTTING-OFF OPERATIONS
a. Use only wheel types that are recommended for your
power tool and the specific guard designed for the
selected wheel. Wheels for which the power tool was not
designed cannot be adequately guarded and are unsafe.
b. Wheels must be used only for recommended
applications. For example: do not grind with the side
of cut-off wheel. Abrasive cut-off wheels are intended for
peripheral grinding, side forces applied to these wheels may
cause them to shatter.
c. Always use undamaged wheel flanges that are of
correct size and shape for your selected wheel.
Proper wheel flanges support the wheel thus reducing the
possibility of wheel breakage. Flanges for cut-off wheels
may be different from grinding wheel flanges.
d. Do not use worn down wheels from larger power tools.
Wheel intended for larger power tool is not suitable for the
higher speed of a smaller tool and may burst.
ADDITIONAL SAFETY WARNINGS SPECIFIC FOR
ABRASIVE CUTTING OFF OPERATIONS
a. Do not "jam" the cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive depth
of cut. Overstressing the wheel increases the loading and
susceptibility to twisting or binding of the wheel in the cut
and the possibility of kickback or wheel breakage.
b. Do not position your body in line with and behind the
rotating wheel. When the wheel, at the point of operation,
is moving away from your body, the possible kickback may
propel the spinning wheel and the power tool directly at you.
c. When wheel is binding or when interrupting a cut for
any reason, switch off the power tool and hold the
power tool motionless until the wheel comes to a
complete stop. Never attempt to remove the cut-off
wheel from the cut while the wheel is in motion
otherwise kickback may occur. Investigate and take
corrective action to eliminate the cause of wheel binding.
d. Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully reenter
the cut. The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
e. Support panels or any oversized workpiece to minimize
the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut and
near the edge of the workpiece on both sides of the wheel.
f. Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
SAFETY WARNINGS SPECIFIC FOR
SANDING OPERATIONS
a. Do not use excessively oversized sanding disc paper.
Follow manufacturers recommendations, when selecting
sanding paper. Larger sanding paper extending beyond the
sanding pad presents a laceration hazard and may cause
snagging, tearing of the disc or kickback.
SAFETY WARNINGS SPECIFIC FOR
POLISHING OPERATIONS
a. Do not allow any loose portion of the polishing bonnet
or its attachment strings to spin freely. Tuck away or
trim any loose attachment strings. Loose and spinning
attachment strings can entangle your fingers or snag on the
workpiece.
SAFETY WARNINGS SPECIFIC FOR
WIRE BRUSHING OPERATIONS
a. Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
b. If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand in
diameter due to work load and centrifugal forces.
c. Do not exceed 15000 min
Do not work with materials containing
WARNING
!
asbestos (asbestos is considered
carcinogenic).
Take protective measures when during
WARNING
!
work dust can develop that is harmful
to one's health, combustible or explosive (some dusts are
considered carcinogenic); wear a dust mask and work with
dust/ chip extraction when connectable.
21
when using wire brushes.
-1