Cleaning, Maintenance, Storage And Ordering Of Spare Parts - Royal RPC 2045 Mode D'emploi

Anleitung_RPC_2045_SPK1:_
GB
Never saw completely through the trunk. Always
leave a hinge. The hinge guides the tree. If the trunk
is completely cut through, control over the felling
direction is lost.
Insert a wedge or felling lever in the cut well before
the tree becomes unstable and starts to move. This
will prevent the guidebar from binding in the felling cut
if you have misjudged the falling direction. Make sure
no bystanders have entered the range of the falling
tree before you push it over.
Warning: Before making the final cut, always
recheck the area for bystanders, animals or
obstacles.
Felling cut
1. Use wooden or plastic wedges (A) to prevent
binding the bar or chain (B) in the cut. Wedges
also control felling (Fig. 13).
2. When diameter of wood being cut is greater than
the bar length, make 2 cuts as shown (Fig. 14).
Warning: As the felling cut gets close to the
hinge, the tree should begin to fall. When tree begins
to fall, remove saw from cut, stop engine, put chain
saw down, and leave area along retreat path (Fig.
11).
Limbing
Limbing a tree is the process of removing the
branches from a fallen tree. Do not remove
supporting limbs (A) until after the log is bucked (cut)
into lengths (Fig. 15). Branches under tension should
be cut from the bottom up to avoid binding the chain
saw.
Warning: Never cut tree limbs while standing on
tree trunk.
Bucking
Bucking is cutting a fallen log into lengths. Make sure
you have a good footing and stand uphill of the log
when cutting on sloping ground. If possible, the log
should be supported so that the end to be cut off is
not resting on the ground. If the log is supported at
both ends and you must cut in the middle, make a
downward cut halfway through the log and then make
the undercut. This will prevent the log from pinching
the bar and chain. Be careful that the chain does not
cut into the ground when bucking as this causes rapid
dulling of the chain. When bucking on a slope,
always stand on the uphill side.
1. Log supported along entire length: Cut from
top (overbuck), being careful to avoid cutting into
the ground (Fig. 16A).
24
12.10.2011 7:43 Uhr Seite 24
2. Log supported on 1 end: First, cut from bottom
(underbuck) 1/3 diameter of log to avoid
splintering. Second, cut from above (overbuck) to
meet first cut and avoid pinching (Fig. 16B).
3. Log supported on both ends: First, overbuck
1/3 diameter of log to avoid splintering. Second,
underbuck to meet first cut and avoid pinching
(Fig. 16C).
Note: The best way to hold a log while bucking is to
use a sawhorse. When this is not possible, the log
should be raised and supported by the limb stumps or
by using supporting logs. Be sure the log being cut is
securely supported.
Bucking using a sawhorse (Fig. 17)
For personal safety and ease of cutting, the correct
position for vertical bucking is essential (Fig. 17).
A. Hold the saw firmly with both hands and keep the
saw to the right of your body while cutting.
B. Keep the left arm as straight as possible.
C. Keep weight on both feet.
Caution: When working with the saw, always
make sure that the saw chain and chain bar are
sufficiently lubricated.
7. Cleaning, maintenance, storage and
ordering of spare parts
Disconnect the spark plug boot before doing any
cleaning and maintenance work!
7.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts
of the equipment. Ensure that no water can seep
into the device.
7.2 Maintenance
Warning: All maintenance work on the chainsaw
apart from the work described in this manual may
only be carried out by authorized after-sales service
personnel.