Table des Matières
Publicité
Multi-Hoop
Multi-Hooping is a special feature in the FUTURA software
that will allow embroidery data which is larger than a single
embroidery hoop to be sent to the machine to stitch out, while
making it easy to re-hoop the fabric so that each part of the
design lines up exactly. This embroidery data may be a single
design that is too large for the hoop or a combination of smaller
embroidery elements and/or lettering, that when combined
together make a much larger finished design. See Fig. 1.
The Multi-Hoop feature splits the design elements in up to four
different parts; and then sews them precisely, matching one
section to the other.
When re-hooping the fabric, the Multi-
hoop feature will compensate for misalignment if the fabric has
been placed slightly askew in the hoop.
When stitching an embroidery design that is too large for the
hoop, it can be difficult to re-hoop the fabric with exact alignment.
Multi-Hoop utilizes a system where three alignment points (A, B,
and C) are input on cross lines that have been marked onto the
fabric. When these points are input, they inform the machine
exactly as to how the fabric is positioned into the hoop and will
therefore sew the design to the alignment of the cross lines. If
the fabric is slightly askew, this system will compensate for it and
sew accordingly. Please note: the Multi-Hoop feature will only
compensate for a slight misalignment in the vertical cross line.
Please try to hoop the fabric as accurately as possible.
Preparing the Fabric
P l e a s e n o t e : T h e f a b r i c m u s t b e l a r g e e n o u g h t o
accommodate the amount of hoops that will be required to
stitch out the design.
1. Using a very fine-lined water soluble marker, mark a line
vertically down the center of the fabric.
2. Mark a line horizontally across the center of the fabric.
The vertical and horizontal lines must be at precise right
angles to each other. These lines will now be referred to
as the"cross lines". These cross lines will be used to set
the fabric into the hoop according to the divided design
layout.
In the Software
1. Select Tools from the horizontal tool bar, select Hoop
and then select Multiple.
2. A single hoop appears on the screen marked with #1 in
the upper left corner.
94
Fig. 1
Fig. 1
Fig. 1
Fig. 2
Fig. 2
Fig. 2
Intersection of cross
lines must be at perfect
90 degree angles.
L'intersection de lignes
de marquage doit être
à un angle parfait de 90
degré.
I n t e r s e c c i ó n d e l a s
líneas de cruce deben
e s t a r e n á n g u l o s
perfectos de 90 grados
Please Note: a thin line is very important to the
accuracy of the final outcome of the embroidery.
Notez s'il vous plaît : Une ligne mince est très importante
pour l'exactitude du résultat final de la broderie.
Por favor Note: una línea delgada es muy importante
para la precisión del resultado final de la bordadora.
Cross line
Fabric
Ligne de
Tissus
marquage
Tela
Línea de
cruce
Cross line
Ligne de
marquage.
Línea de
cruce
Please note: Up to three
a d d i t i o n a l h o o p s w i l l
a p p e a r a s t h e d e s i g n
data requires.
N o t e z s ' i l v o u s p l a î t :
Jusqu'à trois cerceaux
s u p p l é m e n t a i r e s
apparaîtront selon les
exigences du dessin de
broderie.
Por favor Note: Aparecerán
hasta tres aros adicionales
si así lo requieren los
datos de diseño.
Publicité
Table des Matières
