Safety Instructions For Batteries; Technical Data - Roller SmartCut Notice D'utilisation

eng

Safety instructions for Batteries

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
● Only use the battery in the ROLLER power tool. Only then is the battery safe
from dangerous overloading.
● Only use original ROLLER batteries with the voltage specified on the rating
plate. Using other batteries can lead to injuries and risk of fire due to exploding
batteries.
● Use the battery and the rapid charger only in the specified operating
temperature range.
● Only recharge ROLLER batteries in the ROLLER rapid charger. There is a
risk of fire if an unsuitable battery charger is used.
● Charge the battery to full capacity with the rapid charger before using for
the first time. Batteries are delivered partly charged.
● Insert the battery into the battery compartment straight and without force.
There is a risk of bending the battery contacts and damaging the battery.
● Protect the batteries against heat, sunlight, fire, moisture and wet. There is
a risk of explosion and fire.
● Do not use the batteries in areas where there is a risk of explosion and in
the vicinity of inflammable gases, solvents, dust, fumes, liquids for example.
There is a risk of explosion and fire.
● Do not open the battery or modify its construction. There is a risk of explosion
and fire due to short-circuiting.
● Do not use batteries with damaged housings or damaged contacts. Damage
to or improper use of the battery can cause fumes to escape. The fumes can
irritate the respiratory tracts. Let in fresh air and consult a doctor in case of
symptoms.
● Fluid can leak from the battery when used improperly. Do not touch the
fluid. Leaking fluid can cause skin irritation and burns. Rinse off immediately
with water in case of contact. Also consult a doctor if the fluid gets into the eyes.
● Observe the safety instructions on the battery and the rapid charger.
● Keep unused batteries away from paper clips, coins, keys, nails, screws
or other small metal objects which could cause bridging of the contacts.
There is a risk of explosion and fire due to short-circuiting.
● Remove the battery before stowing/storing the power tool for long periods
of time. Protect the battery contacts against short-circuiting, e.g. with a cap.
● Do not throw defective batteries in the normal household waste. Hand the
defective batteries over to an authorised ROLLER contract service workshop or
a recognised disposal company. Observe the national regulations.
Explanation of symbols
WARNING
Danger with a medium degree of risk which could result in death
or severe injury (irreversible) if not heeded.
CAUTION Danger with a low degree of risk which could result in minor injury
(reversible) if not heeded.
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating instructions before use
ROLLER'S SmartCut complies with protection class I
ROLLER'S Akku-SmartCut and rapid charger comply
with protection class Il
Environmentally friendly disposal
CE conformity mark

1. Technical Data

Use for the intended purpose
WARNING
ROLLER'S SmartCut and ROLLER'S Akku-SmartCut are intended for the purpose
of cutting pipes.
All other uses are not for the intended purpose and are prohibited.
1.1. Scope of Supply
ROLLER'S
SmartCut: Electric pipe cutting machine (without cutting wheel),
single open-ended wrench size 8, operating instructions,
carrying case.
ROLLER'S
Akku-SmartCut: Cordless pipe cutting machine (without cutting wheel),
Li-Ion battery, Li-Ion/Ni-Cd rapid charger, single
open-ended wrench size 8, operating instructions,
carrying case.
1.2. Article numbers
ROLLER'S SmartCut
ROLLER'S Akku-SmartCut
ROLLER High-Power-Battery Li-Ion 10.8 V, 1.3 Ah
Rapid-charger Li-Ion/Ni-Cd 230 V, 50 – 60 Hz, 65 W
ROLLER cutting wheel Cu-INOX
ROLLER cutting wheel V
ROLLER'S Assistent 3B
ROLLER'S Assistent WB
ROLLER'S Werkmeister
ROLLER'S Werkmeister E
Carrying case
1.3. Application Area
ROLLER'S SmartCut, ROLLER'S Akku-SmartCut:
Pipes of pressfitting systems made of
● stainless steel, C-steel (not jacketed)
● semi-hard and hard copper
● composite pipes
1.4. Speed
ROLLER'S SmartCut, ROLLER'S Akku-SmartCut:
Idle speed of cutting wheel
1.5. Electrical Data
ROLLER'S SmartCut:
230 V~; 50 – 60 Hz; 130 W
Fuse (mains) 10 A (B), cut-out operation S3 20% AB 2/10 min,
radio interference suppressed, protection class I, PE conductor as of
machine no. 3650
ROLLER'S Akku-SmartCut:
10.8 V =, 16 A, 270 W
Rapid-charger
Li-Ion/Ni-Cd
1.6. Dimensions
ROLLER'S SmartCut:
L × W × H:
ROLLER'S Akku-SmartCut:
L × W × H:
1.7. Weights
ROLLER'S SmartCut
ROLLER'S Akku-SmartCut drive machine without battery
1.8. Noise Data
Workplace-related emission
value
1.9. Vibrations
Weighted effective value of the acceleration
The indicated weighted effective value of acceleration has been measured
against standard test procedures and can be used by way of comparison with
another device. The indicated weighted effective value of acceleration can also
be used as a preliminary evaluation of the exposure.
CAUTION
The indicated weighted effective value of acceleration can differ during operation
from the indicated value, dependent on the manner in which the device is used.
Dependent upon the actual conditions of use (periodic duty) it may be necessary
to establish safety precautions for the protection of the operator.
2. Start-up
2.1. Electrical Connection
WARNING
Caution: Mains voltage present! Before connecting the electric pipe cutting
machine or the rapid charger, check whether the voltage given on the rating
plate corresponds to the mains voltage. Only use sockets/extension leads with
a functioning protected earth contact for ROLLER'S SmartCut. On building
sites, in a wet environment, indoors and outdoors or under similar installation
conditions, only operate the electric pipe cutting machine on the mains with a
fault current protected switch (FI breaker) which interrupts the power supply
as soon as the leakage current to earth exceeds 30 mA for 200 ms.
Rechargeable batteries
NOTICE
Always hold the battery (9) upright when inserting it in the drive unit or the rapid
charger. If inserted at an angle it can cause damage to the contacts and result
in a short circuit which damages the battery.
Total discharging by undervoltage
The Li-Ion batteries may not drop below a minimum voltage because otherwise
the battery could be damaged by "total discharge". The cells of the ROLLER
Li-Ion battery are delivered pre-charged to approx. 40 %. Therefore the Li-Ion
batteries must be charged before use and recharged regularly. Failure to observe
this regulation of the cell manufacturer can lead to damage to the Li-Ion battery
844000
by total discharging.
844001
Total discharging due to storage
844510
571560 If a relatively low charged Li-Ion battery is stored, self discharging can lead to
Input 230 V~; 50 – 60 Hz; 65 W, protection class II
Output 10.8 – 18 V – ---
Input 100 – 120 V~; 50 – 60 Hz; 65 W, protection class II
Output 10.8 – 18 V – ---
405 × 90 × 103 mm (15.9"× 3.5"× 4")
408 × 88 × 105 mm (16"× 3.4"× 4.1")
L = 78 dB L = 67 dB L
wA pA
eng
844050
844051
120120
120130
120200
120240
574436
Ø 12 – 28 mm
Ø 10 – 35 mm
Ø 10 – 40 mm
130 min‫¹־‬
1.9 kg (4.2 lb)
2.0 kg (4.4 lb)
= 87 dB K = 3 dB
pC, peak
1.2 m/s² K = 1.5 m/s²