Kenmore 587.1529 Série Guide D'utilisation Et D'entretien page 10

Operating Instructions
Wash Cycle Selections
Note: Cycle times are approximate and
will vary with options selected. hot water is
necessary to activate dishwasher detergent and
melt fatty food soils. An automatic sensor will
check the incoming water termperature and, if
it is not hot enough, the timer will be delayed
for automatic water heating in the main wash
of all cycles. This happens even when HI-TEMP
WASH is selected, an even higher temperature
will be guaranteed to handle heavier soil loads.
Option Selections
Wash Pressure (available on select
models)
The programmed cycles default to the Medium
pressure option which varies the pressure
optimally for the cycle's intended normal use.
For special circumstances, either a Light or
Heavy pressure is desire that may be selected.
To accure best wash cycle performance, some
pressure options are not selectable in all wash
cycles.
Favorite Cycle
The FAVORITE CYCLE option allows you to
program your preferred cycle and optios into
one button. Once Programmed, simply press the
Favorite Cycle button followed by the START/
CANCEL pad.
To Program the FAVORITE CYCLE button:
1. Select the preferred cycle button.
2. Hold the FAVORITE CYCLE button for 3
seconds.
The display will fl ash for 2 seconds indicating
the FAVORITE CYCLE option has been
programmed. To change the FAVORITE CYCLE
option simple repeat steps one and two above.
Max Dry
When MAX DRY option is selected, the
dishwasher increases the temperature of
the fi nal rinse and extends drying time by
approximately twenty miniutes. The MAX
DRY option can be used with all cycles except
ENERGY SAVER and QUICK RINSE. For
best drying performance, select Hi-Temp
Wash and/or Sanitize. This will increase the
temperature during the wash cycle to improve
drying.
The energy required to use the MAX DRY
option costs pennies per cycle. You may
choose not to select the MAX DRY option;
however you may have items in your dish load
that will not be completely dry at the end of
the cycle.
Hi-Temp Wash
When HI-TEMP WASH option is selected, the
dishwasher heats water in the main wash to
approximately 140
This increase in water temperature helps
dishwasher detergent remove food grease and
soil from dishes more eff ectively and aids in
drying. This option is available in NORMAL
WASH and TOP RACK. HI-TEMP WASH is
automatically provided when HEAVY WASH
cycle is selected.
Air Dry
The AIR DRY option is used to de-activate the
heating element during the drying phase of the
selected wash cycle. This option will slightly
decrease energy usage but will increase the
likelihood that dishware will not be dry.
Sanitize
To sanitize your dishes and glassware, select
the SANITIZE option. When selected, the light
above the pad will come on and remain on
until end of cycle. The water temperature in
the fi nal rinse will be raised to 155
assuring bacteria is destroyed. This option
is available in NORMAL WASH and TOP
RACK. SANITIZE is automatically provided
when HEAVY WASH is selected. Only these
sanitization cycles have been designed to meet
NSF requirements.
The cycle time will be extended until the
proper water temperature is reached.
Washing action will continue during the water
heating delay. For best results, the incoming
water temperature should be at least 120
(49 0 C).
The sanitize criteria may not be satisfi ed if
there is an interruption of the cycle, power
failure or if the incoming water temperature is
below 120 F (49 C).
0 0
To turn off the SANITIZE option, press the pad
a second time. The light above the pad will
turn off .
To Cancel a Cycle
You can cancel a cycle anytime during the
cycle. Press START/CANCEL pad and the
dishwasher will start a 90 second drain. At the
end of the drain, select the desired cycle.
10
F (60 C).
0 0
F (68
0
C)
0
F
0