Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Copying Physical
Fader Assignment
Fader Reverse
(0–255/255–0)
Resetting the
System
4. Programming
Entering Program
Mode
Exiting Program
Mode
Creating a Scene
Obey 70 User Manual Rev. 7
This process will copy the physical fader assignment from one fixture into another.
Press <PROGRAM> and <TAP SYNC/DISPLAY>. This will enter the physical fader
1.
assignment mode.
2.
Press & hold the fixture button that contains the desired physical fader assignment.
3.
While still holding the previous fixture button, press & hold the fixture that you want to copy
into.
4.
While still holding the two fixture buttons above, press & hold <MIDI/ADD>.
5.
While still holding all three buttons down, release the fixture selected in step # 2 above.
While still holding down <MIDI/ADD>, release the fixture selected in step # 3 above.
6.
Release <MIDI/ADD>.
7.
8.
All fixture LEDs will flash.
9.
Press <PROGRAM> and <TAP SYNC/DISPLAY> two times to exit physical fader
assignment mode.
This will not copy the fader-reverse setting(s).
This function will allow you to reverse the DMX output of the physical fader(s).
1.
Press <PROGRAM> and <TAP SYNC/DISPLAY> two times. This will enter the fader
reverse assignment mode.
2.
Select one of the fixtures: <FIXTURE 1–12> (this will be the fixture that you want to modify
the channels for).
Move the <SPEED> fader to select the physical slider (control channel).
3.
4.
Move the <FADE TIME> fader to activate/deactivate this function.
5.
Press <MIDI/ADD> to save the setting.
6.
Repeat steps 3–5 until all of the faders have been assigned for the fixture.
7.
Press <PROGRAM> and <TAP SYNC/DISPLAY> one time to exit fader reverse
assignment mode.
Use this function to revert all settings and scenes back to the state they were in
when the product left the factory.
1.
Turn off the unit.
2.
Press and hold <BANK UP> and <AUTO/DEL>.
3.
Turn on power to the unit (while still holding <BANK UP> and <AUTO/DEL>).
4.
All LEDs will blink to indicate a successful reset.
This will erase all scenes, chases, and other settings! This process may take
up to 30 seconds to complete.
No programming may be done on the Obey 70 without first entering program mode.
You will find references to this process in many other sections of this user manual.
Press and hold <PROGRAM> for three seconds to exit program mode.
1.
Turn on the controller.
2.
Press and hold <PROGRAM> for three seconds.
3.
When the LED displays Program LED lights, you have entered program mode.
You will find references to this process in many other sections of this user manual.
While currently in program mode, press and hold <PROGRAM> for three seconds.
1.
2.
When the LED display Program LED turns off, you have exited program mode.
Use this function to create a static look on stage.
1.
Turn on the controller.
2.
Enter program mode.
3.
Select one or more fixtures.
4.
Using the 8 sliders, modify the value of the desired channel(s).
When the desired look has been achieved, press <MIDI/ADD>.
5.
6.
Use <BANK UP/DOWN> to select a desired bank (30 possible) to save the scene to.
7.
Once you have navigated to the desired bank, press the <SCENE> (1–8) to save the
scene directly to.
8.
All LEDs will flash to indicate that the scene has been saved.
9.
Repeat steps 3–8 until you are finished programming all scenes.
10. Exit program mode.
You may select more than one fixture at a time. If you do so, you will not have
separate control over each of them. You may program multiple fixtures into the
same scene.
Use PAGE A/B to switch between the 2 pages for the selected fixture.
Page 13 of 69
Publicité
Table des Matières
