Using The Tft Monitor; Open/Close Tft Monitor; Tft Monitor Auto Open; Monitor Tilt Angle Adjustment - Audiovox PHOSE Série Guide D'instructions

UV7

USING THE TFT MONITOR

Open/Close TFT Monitor

Press the OPEN button (1) on the front panel or press the
( ) button (25) of the front zone remote control to activate
the mechanism that moves the display panel into the viewing
position.
Press the OPEN button (1) on the front panel or press the
( ) button (25) of the front zone remote control to load the
display panel back into the compartment.

TFT Monitor Auto Open

If "TFT Auto Open" is "on" when the unit is turned on, the
monitor automatically moves to the viewing position.
If "TFT Auto Open" is "off" when the unit is turned on, press
the OPEN button (1) or ( ) button (25) on the front zone
remote control to move the monitor into the viewing position.
If "TFT Auto Open" is set to "Manual", the TFT will not close
when the key is turned off.

Monitor Tilt Angle Adjustment

A known characteristic of LCD panels is the quality of the
display in relationship to the viewing angle. The monitor
angle can be adjusted for optimum viewing using one of the
following methods:
Step by Step Angle Adjustment
Press the ( ) or ( ) button (3, 4) on the monitor frame to
adjust the tilt angle of the screen one step at a time.
Continuous Angle Adjustment
Press and hold the ( ) or ( ) button (3, 4) on the monitor
frame to adjust the tilt angle in a continuous motion.

Aspect Ratio

Press the WIDE button (28) on the remote control or WIDE/
PICTURE button (2) on the monitor to adjust the aspect ratio
as follows:
CINEMA
The entire screen is extended
horizontally to the aspect ratio of 16 to
9. The extension ratio is the same at
any point.
NORMAL
The conventional display image has a
4 to 3 ratio of horizontal to vertical,
leaving a blank area on the right and
left sides of the display.
OFF

Image Setting

Table 2 shows the video output mode for each playing
source.
Table 2: Video Output Modes
Playing Source Video Output Modes
AM/FM TUNER YUV Mode
XM TUNER YUV Mode
iPod YUV Mode
DVD YUV Mode
AUX IN CVBS Mode
*CVBS – Composite Video Baseband Signal
Parameter Adjustment Procedure
1. Enter Picture Quality Setting mode:
Press the PIC button (24) on the remote or press and
hold the WIDE/PICTURE button (2) on the monitor
panel.
2. Select Item to Set:
Press the (>>) ( ) buttons (14, 22) on the remote or
<<
press and hold the (/\) or (V) buttons (18, 19) on the
monitor panel.
3. Set Parameters:
Press (|<<) (>>|) buttons (17, 19) on the remote or press
(<) (>) buttons (16, 17) on the monitor panel.
4. Exit Picture Quality Setting Mode:
Press the PIC button (24) on the remote or press and
hold the WIDE/PICTURE button (2) on the monitor
panel.

Parking Brake

Parking Brake Inhibit
When the pink "Parking" wire is connected to the vehicle
brake switch, the front TFT monitor will display video only
when the parking brake sequence is engaged. Before starting
the parking brake sequence, the radio must be on with the
video media disc inserted and playing.
Parking Brake Sequence
There are two situations that can start the Parking Brake
Sequence:
• Parking brake is engaged (on) when the vehicle is started
or the accessory / ignition is turned on. To activate video,
the following sequence of events must be completed:
a. Release parking brake for 1 second.
b. Reapply the parking brake.
11
c. Video should be displayed on the TFT monitor within 1
~ 2 seconds.
• Parking break is disengaged (off) when the vehicle is
started or the accessory / ignition is turned on. To activate
video, the following sequence of events must be
completed:
a. Set parking brake for 1 second.
b. Release parking brake for 1 second.
c. Reapply parking brake.
d. Video should be displayed on the TFT monitor within 1
~ 2 seconds.

Monitor Movement Mechanism

If an obstruction occurs in the monitor path, the following
protective measurements can be executed to prevent
damage to the mechanism or monitor:
Table 3: Monitor Protective Measures
Self OPEN Button
Obstruction
Protection Pressed
Monitor load- Monitor is auto- Monitor fully
ing out hori- matically extended hori-
zontally loaded into unit zontally
Monitor load- Unit stops at Monitor fully
ing in hori- obstruction extended hori-
zontally point zontally
Monitor load- Unit stops at Monitor swiv-
ing out verti- obstruction els back to the
cally point unit
Monitor load- Unit stops at Monitor swiv-
ing in verti- obstruction els back to the
cally point unit
After the protective procedure is executed, normal operation
is resumed by pressing the OPEN button (1) or disconnecting
and reconnecting the power.
Power
Reconnected
Monitor is auto-
matically
loaded into unit
Monitor is auto-
matically
loaded into unit
Monitor swiv-
els back to the
unit
Monitor swiv-
els back to the
unit