Publicité
Les langues disponibles
Les langues disponibles
REMEMBER! When using the device, protect children
and other bystanders.
3.3 Personal safety
a)
Do not use the device when tired, ill or under the
influence of alcohol, narcotics or medication which
can significantly impair the ability to operate the
device.
b)
When working with the device, use common sense
and stay alert. Temporary loss of concentration
whilst using the device may lead to serious injuries.
c)
Use personal protection equipment as required
for working with the device, specified in section 1
(Legend). The use of correct, approved personal
protection equipment reduces the risk of suffering
an injury.
d)
To prevent the device from accidentally switching on,
make sure the switch is on the OFF position before
connecting to a power source.
e)
Do not overestimate your abilities. When using the
device keep your balance and remain stable at all
times. This will ensure better control over the device
in unexpected situations.
f)
Do not wear loose clothing or jewellery. Keep hair,
clothes and gloves away from moving parts. Loose
clothing, jewellery or long hair may get caught in
moving parts.
g)
Remove all adjusting tools or spanners before
turning the device on. A tool or spanner left in the
revolving part of the device may cause injury.
3.4 Safe device use
a)
Do not overload the device. Use appropriate tools
for the given task. A correctly selected device will
perform the task for which it was designed better
and in a safer manner.
b)
Do not use the device if the ON/OFF switch does not
function properly (does not switch the device on and
off). Devices which cannot be switched on and off
using the ON/OFF switch are hazardous, should not
be operated and have to be repaired.
c)
When not in use, store in a safe place, away from
children and people not familiar with the device, who
have not read the user manual. The device may pose
a hazard in the hands of inexperienced users.
d)
Maintain the device in a good technical state. Before
each use check for general damage and especially
check for cracked parts or elements and for any other
conditions which may impact the safe operation of
the device. If damage is discovered, hand over the
device for repair before use.
e)
Keep the device out of the reach of children.
f)
Device repair or maintenance should be carried out
by qualified persons, only using original spare parts.
This will ensure safe use.
g)
To ensure the operational integrity of the device, do
not remove factory fitted guards and do not loosen
any screws.
h)
When transporting and handling the device between
the warehouse and the destination, take into account
the occupational health and safety principles for
manual transport operations which apply in the
country where the device will be used.
i)
Avoid situations where the device halts during
use due to excessive loading. This may result in
overheating of the drive elements and device
damage.
8
j)
Do not touch articulated parts or accessories, unless
the device has been disconnected from a power
source.
k)
Use insulated handles to grip the device. Ensure that
the metal tools attached to the device do not come
into contact with a live wire. Risk of electric shock.
l)
The specified vibrations emission was measured
using standard measurement methods. Vibrations
emissions may change if the device is used in
different surroundings.
m)
When changing attachments and rotation direction
make sure the device is switched off and locked.
n)
In order to prevent unintentional activation during
storage,
when
installing/removing
batteries,
replacing attachments etc. make sure the rotation
direction selector is in the middle position – locked.
4. Use guidelines
The cordless drill screwdriver is designed to drill holes,
drive in, tighten and drive out bolts, screws, etc. attachment
elements.
The user is liable for any damage resulting from non-
intended uses of the device.
4.1 Device description
2
3
4
1
10
2a
5
9
2b
6
3
13
7
11
8
12
1.
Jaws
2.
Chuck
2a.
Chuck
2b.
Ring
3.
Adjustment ring
4.
Gear selector
5.
Direction switch
6.
Handle
7.
Battery snap fasteners
8.
Battery
9.
On/Off trigger
10.
LED illumination
11.
Highest torque value setting symbol
12.
Indicator
13.
Torque setting values for driver mode
4.2 Preparing for use
Battery charging
Attention: To connect / disconnect the battery make sure the
device if off.
•
Squeeze the battery on both sides at the snap
fasteners (7) and then slide the battery out of the
device.
•
Connect the charger to a power source.
•
Connect the battery to the charger. A red light will
come on the charger. The charger may be warm and
emit a buzzing sound. This is normal and does not
indicate incorrect operation.
Rev. 02.03.2018
•
Once the battery is fully charged, a green light will
come on the charger. Disconnect the charger from
the power source and reinsert the battery into the
device.
Tool attachment
•
Before attaching/removing a work tool, ensure the
device is switched off.
•
Only use correct size work tools.
•
To install an attachment (drill bit or screwdriver bit),
grip the ring (3) and twist the chuck (2) anticlockwise,
until the jaws open sufficiently to insert the required
attachment.
Insert the attachment into the chuck jaws, then grip the ring
(3) and rotate the chuck (2) clockwise to firmly secure the
attachment. To remove an attachment, follow the above
steps in reverse order.
4.3 Device use
STARTING THE DEVICE
To start the device press and hold the On/Off trigger (9);
once the trigger is released, the device will stop.
The illumination diode will come on automatically once the
On/Off trigger is pressed and will go off once the trigger is
released.
Changing direction
It is possible to change the revolution direction (clockwise/
anticlockwise). To select a given direction, slide the switch (5)
all the way to the right or left. To change spin direction, make
sure the device is off. Positioning the switch (5) in the middle
locks the device against accidental activation.
Gear selection
The cordless drill screwdriver features a selection of gears,
which deliver various rotational speed ranges. To change
gears, move the gear selector (4) between positions 1 and
2. Operation with a setting between positions 1 and 2 may
damage the device. Change gears with the device switched
off.
Setting torque
The device has 19 torque settings. To change, rotate the
adjustment ring (3), until the required setting is aligned with
the indicator (12).
Select a torque to match the parameter of the work material.
Tests on another element made of the same material are
recommended, in order to determine the optimal torque
setting.
Rev. 02.03.2018
Attention: Do not use the device when the torque is set
between the highest driver setting and the drilling setting.
Operation in this position may result in device damage.
Device functions
The cordless drill screwdriver features a dual function:
driving and drilling.
Driving function:
•
Install the required screwdriver bit in the chuck jaws.
•
Select torque setting.
•
Insert the tip of the screwdriver bit into the grooves
on the screw head. The screwdriver bot should be
perpendicular to the screw head.
•
Press the On/Off trigger gently to start the device.
Increase the speed gradually by depressing the On/
Off trigger further. Do not use excessive force when
driving.
•
Once the screw is in, release the On/Off trigger.
•
Before driving screws into wooden elements, drill
a pilot hole to prevent work material damage (e.g.
cracks). The recommended pilot hole sizes for given
wood screw diameters are shown in the table below.
Wood screw size
Φ
Φ
Φ
Φ
Φ
[mm]
3,1
3,5
3,8
4,5
4,8
Pilot hole size
Φ
Φ
Φ
Φ
Φ
[mm]
2,0
2,2
2,5
2,9
3,1
÷2,2
÷2,5
÷2,8
÷3,2
÷3,4
Wood screw size
Φ
Φ
Φ
Φ
[mm]
5,1
5,5
5,8
8,0
Pilot hole size
Φ
Φ
Φ
Φ
[mm]
3,3
3,5
3,8
5,0
÷3,6
÷3,9
÷4,1
÷5,5
Drilling function
•
Set torque to a driver setting (11).
•
Install required size drill bit in the chuck jaws.
•
For drilling in metal, punch the hole position before
starting drilling to avoid the drill bit from slipping.
When drilling in metal, use lubricants (with the
exception of iron and brass).
•
When the drill bit is about to break through to the
other side of the workpiece, reduce pressure and
grip the device firmly.
•
If the drill bit snags during drilling, attempt to
remove it by changing the rotation direction to
anticlockwise (warning: kick back may occur).
4.4 Cleaning and maintenance
•
Before cleaning, remove the battery from the device.
•
Use cleaners without corrosive substances to clean
each surface.
•
Clean the vents with a paintbrush and compressed
air.
•
Do not leave the battery in the device, if it will not be
used for a long time.
•
Store the unit in a dry, cool place, free from moisture
and direct exposure to sunlight.
SAFE REMOVAL OF BATTERIES AND RECHARGEABLE
BATTERIES
The device uses a 10.8 V lithium-ion battery.
Worn batteries must be removed from the device
proceeding analogously to their installation.
Recycle batteries.
9
Publicité
