Hoonved CAP 10 E Mode D'emploi page 31

Part 2: For the operator
2.1.h Reading the TEMPERATURES
At any time, with the machine switched ON or OFF, by
pressing the "SI" button you can read, in sequence, the
REAL and PROGRAMMED temperatures for the water in
the tank (t1) and in the boiler (t2).
- Pressing the "SI" button once, the message "t1" will be
displayed
-Pressing the "SI" button a second time, the REAL tempe-
rature of the water in the tank will be displayed;
- Pressing the "SI" button a third time, the PROGRAMMED
temperature of the water in the tank (for the selected
cycle) will be displayed;
- Pressing the "SI" button a fourth time, the message "t2"
will be displayed, indicating the boiler;
- Pressing the "SI" button a fifth time, the REAL temperature
of the water in the boiler will be displayed;
- Pressing the "SI" button a sixth time, the PROGRAMMED
temperature of the water in the boiler (for the selected
cycle) will be displayed;
- Pressing the "SI" button a seventh time, the machine will
return to its initial status.
ATTENTION
The operations listed above CANNOT BE CARRIED OUT
DURING A CYCLE.
2.1.i REGENERATION OF THE RESINS
(only for CAP10DE-CAP12DE-SO100DE-SO120DE)
The regeneration should be carried out at the end of the
working day. In case of very hard water, please make the
regeneration more often.
First of all, please make sure that the salt container is full
with regeneration salt, then do what follows:
1. unscrew the container's cap and fill in 1Kg of regeneration
salt;
2. Tighten again the container's cap in order to
hermetically seal the container.
REGENERATION OPERATIONS
With the machine TURNED OFF (ON/OFF button (IL) on
OFF), with FULL tank and CLOSED door, keep the "SD" or
CYCLE button pressed for at least 5 seconds; "C3" will
appear on the display;
LC1 LC2 LC3 LC4
LC1 LC2 LC3 LC4
LC1 LC2 LC3 LC4
LC1 LC2 LC3 LC4
LC1 LC2 LC3 LC4
LC1 LC2 LC3 LC4
The REGENERATION CYCLE will start. The display
LEDs flashing in sequence will show that the cycle is
running.
At this point the machine will automatically execute all
the necessary operations (20 minutes time approx.).
During the regeneration cycle, the machine will not be
operative.
BEWARE
Opening the door will stop the REGENERATION
CYCLE; by closing the door, the cycle will be continued
from where it was interrupted.
IMPORTANT
The cycle can be stopped in any moment by pressing the
"SD" or CYCLE button for at least 5 seconds.
For re-starting the cycle, just press the "SD" or CYCLE
button again (the cycle will be continued from where it was
interrupted).
After ending the regeneration cycle, the machine is
again ready for use.
2.1.l Switching off the CAP/SO Ewasher at the end of the
day
At the end of the working day SWITCH OFF the CAP/
SO E washer by pressing the "IL" button.
Switch off the mains switch feeding the machine and
close the water supply taps.
For any repairs, contact only assistance centres
authorised by the manufacturer.
WARNINGS DURING OPERATION
1) Ensure that the washing temperature remains at
approx. 55-60°C;
2) Avoid immersing bare hands in the detergent-filled
water; if this should happen, rinse immediately and
thoroughly with running water;
3) Use only anti-foaming detergents with chlorine-active
agents, specific for use in industrial machines;
4) Deactivate the machine in case of break-down or
malfunction.
For any repairs, contact only assistance centres
authorised by the manufacturer, and insist on the use of
original parts.
5) In no case should you change the programmed
temperatures (t1 and t2) without first consulting an
authorised assistance centre;
Failure to follow the above warnings may compromi-
se the safety of the washing machine.
Useful advice for better washing results
Any unsatisfactory results from washing can be seen
when traces of dirt are left on dishes or other items; any
water marks may be caused by insufficient rinsing.
In this case, ensure that the rinsing nozzles (24) are
clean and that there is pressure in the water system.
If there are traces of waste, ensure that:
- The filters (26) (30) are clean;
- the water temperature is around 60°C;
- items are correctly positioned in the basket;
- the washing nozzles are clean;
- the wash arms (23) (25) rotate freely.
ENGLISH
31