Modifying A Washing Programme; Automatic Safety Systems - Fagor FET-6412WS Guide D'utilisation

EN 4 / PROGRAMMING YOUR MACHINE

•MODIFYING A WASHING PROGRAMME

•During programming:
Anything can be changed before the "Start/Pause" button
•After the cycle has started:
If you want to change the type of fabric (e.g. from "COTTON" to
„SYNTHETICS") after you have pressed the "Start/Pause" button"
you have to cancel the current programme. To do this, turn the selector
1
to " ".
Then programme your new selection remembering to confirm it by
pressing the „Start/Pause" button
NB: If you change the programme without first
cancelling it, the machine displays:
This indicates that the new selection has not been
registered.
On the other hand, the current cycle is not cancelled and if you turn
the selector switch 1 back to its original position, this cycle will resume.
•Throughout the cycle:
The following changes are possible without pressing the "Start/Pause"
button 6 .
— You can change the temperature for the same type of textile.
N B: If the temperature achieved by the washing cycle is higher than your
new selection, heating the water stops immediately and the cycle
continues.
— You can alter the spin speed throughout the cycle.
— You can select "Drip Dry" and "Full drum stop" throughout the washing
phase.
— You can activate the "Rinse plus" (
the cycle progress light "
illuminates).
•During the period before the cycle actually starts
have chosen to delay the time your washing starts):
— Any kind of programme modification is accepted during a delayed
start's waiting period.
— You can alter the length of a delayed start throughout the waiting period
before the cycle effectively starts. To do this, press the ( + ) or (-) buttons
5
to select a new value.
NB:
- During this period, selecting a new time cancels out the previous
selection. The new period selected is accepted based on the last selection
made.
- If, during this time, you wish to completely cancel the "delayed start",
press either the (+) button or the (-) button until the „ " light goes out
and the „ " light comes on.
Then briefly press "Start/Pause"
The cycle will start immediately.
•When the cycle is over:
When the machine shows "StOP", you can programme a new cycle
without having to reset the selector
For this, all you have to do is turn the selector or press one of the buttons
2 , 3 or 4 .
The machine displays the time of the previously selected programme.
The machine is then ready to be reprogrammed.
6 is pressed.
6 .
) option until rinsing starts (until
"
6 .
1
to the " " position.

•AUTOMATIC SAFETY SYSTEMS

•Lid opening safety system:
As soon as washing commences, the lid on your machine is locked.
When the cycle is finished or when the machine has stopped with the
drum full of water, the lid unlocks.
If you have selected a delayed wash, the lid remains unlocked throughout
6
,
the waiting period until the cycle actually starts.
If you wish to open the lid during the cycle, press button "Start/Pause"
6 briefly and wait 1-2 minutes for the safety system to unlock the lid.
Important:
Depending on when you wish to open the lid during the cycle,
this time delay may be a little longer because a cooling down period
may also have to be included.
In fact, to avoid your being severely burnt, the lid safety system will
not open during the cycle unless the temperature inside the machine
is below a certain threshold.
•Water safety system:
During operation, constant control of the water prevents any overflows.
•Spin safety system:
Your washing machine is fitted with a safety system that restricts the
spin when poor load distribution is detected.
In this case, your washing may be insufficiently spun. Redistribute
your washing in the drum and programme a new spin.
•Anti-foam system:
Your machine can detect when too much foam is being produced during
spinning.
At such times, spinning stops and the machine drains.
The cycle then restarts, adapting the spin rates and possibly adding
an extra rinse.
(if you
32