GreenWorks Tools 3200007 Manuel D'utilisation page 4

EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
position.
■ Turn the side handle clockwise to securely tighten.
OPERATION
WARNING
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
WARNING
Always remove battery pack from the tool when you
are assembling parts, making adjustments, cleaning,
or when not in use. Removing battery pack will
prevent accidental starting that could cause serious
personal injury.
WARNING
Always wear eye protection. Failure to do so could
result in objects being thrown into your eyes resulting
in possible serious injury.
WARNING
Do not use any attachments or accessories not
recommended by the manufacturer of this product.
The use of attachments or accessories not
recommended can result in serious personal injury.
Applications
You may use this product for the purpose listed below:
■ Grinding metals
■ Sanding wood or metal surfaces
WARNING
Battery products are always in operating condition.
Therefore, the switch should always be locked when
not in use or carrying at your side.
Starting And Stopping The Angle Grinder (see
figure D - E)
■ To start the power tool, push the On/Off switch
forwards.
■ To lock the On/Off switch, press the On/Off switch
down at the front until it latches.
■ To switch off the power tool, release the On/Off
switch or, if it is locked, briefly push down the back of
the On/Off switch and then release it.
■ To save energy, only switch the power tool on when
using it.
■ Check grinding tools before using. The grinding
tool must be mounted properly and be able to
move freely. Carry out a test run for at least one
minute with no load. Do not use damaged, out-
of-centre or vibrating grinding tools. Damaged
grinding tools can burst and cause injuries.
English (Original Instructions)
4
Positioning The Guard (see figure F - I)
■ The guard on the grinder should be correctly positioned
depending on which side the handle is mounted. Never
use the grinder without the guard correctly in place.
WARNING
Never place the guard so that it is in front of the
grinder. This could result in serious injury because
sparks and loose particles thrown from the grinding
wheel would be directed toward the operator. Always
place the guard in the correct location as shown.
To reposition the guard:
■ Remove the battery pack.
■ Unlock the guard clasp by pulling the clasp out, away
from the grinder.
■ Rotate the guard to its correct position as shown.
■ Lock the guard clasp by pushing the clasp in.
NOTE
: Be sure the raised ridge on the guard is
seated in the groove on the bearing cap. Never use
the grinder without the guard in place and properly
adjusted.
Operating The Grinder (see figure J)
Always carefully select and use grinding wheels that
are recommended for the material to be ground.
Make sure that the minimum operating speed of any
accessory wheel selected is 6,500 r/min. or more. The
grinding wheel provided with the grinder is suitable
for grinding welds, preparing surfaces to be welded,
grinding structural steel, and grinding stainless steel.
To operate the grinder:
■ Secure all work in a vise or clamp to a workbench.
DANGER
Never use the grinder with the guard removed. It has
been designed for use only with the guard installed.
Attempting to use grinder with guard removed will
result in loose particles being thrown against the
operator resulting in serious personal injury.
■ Hold the grinder in front and away from you with
both hands, keeping the grinding wheel clear of the
workpiece.
■ Turn on the grinder and let the motor and grinding
wheel build up to full speed.
■ Lower the grinder gradually until the grinding wheel
contacts the workpiece.
WARNING
To prevent loss of control and possible serious
personal injury, always operate the grinder with both
hands, keeping one hand on the side handle.
■ Keep the grinder tilted at an angle from 5° to 15° and
continuously moving at a steady, consistent pace.
NOTE: If the grinder is held in one spot too long, it will