Intended Use; Before Starting Work - Baier BSM 287 Traduction Du Mode D'emploi Original

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

3.4

Intended Use

BAIER high-speed mixers are suitable for stirring
paints, plasters, mortars, adhesives and similar
materials. They may not be used to stir food, highly
flammable or caustic substances.
4

Before Starting Work

To ensure safe working with the high-speed mixers,
the following points must be observed before each
use:
Read through all safety instructions and
warnings in this instruction manual.
Wear protective clothing such as hard hat, face
protection or safety goggles, safety gloves and if
necessary an apron.
The voltage on the rating plate must be identical
with the mains voltage.
Before using the machine, always check the
connection cable and plug.
/
Test the personal protection switch
7
13
(only BSM 2863 – 110 V)
DANGER
Risk of injury due to electric shock.
Î The PRCD personal protection switch must be
checked each time before the BSM 2863 – 110
V high-speed mixer is started up (see below).
If the PRCD does not trip during the test, or if
it switches off repeatedly when the BSM 2863
– 110 V high-speed mixer is switched on, the
BSM 2863 – 110 V high-speed mixer together
with the PRCD personal protection switch must
be examined by a qualified electrician.
13
If the mains plug is plugged in and the
BSM 2863 – 110 V high-speed mixer is switched
off, press the −ON− button (RESET) (2). The red
indicator light (1) must light up.
Press the −OFF− button (TEST) (3). The
13
PRCD must switch off, i.e. the red indicator light
(1) goes out.
Press the −ON− button again (RESET) (2).
13
It must now be possible to switch on the
BSM 2863 – 110 V high-speed mixer.
If the PRCD does not trip during the test, or if
it switches off repeatedly when the BSM 2863
– 110 V high-speed mixer is switched on, the
BSM 2863 – 110 V high-speed mixer together
with the PRCD personal protection switch must
be examined by a qualified electrician.
Operation of the BSM 2863 – 110 V high-
speed mixer with a defective PRCD personal
protection switch is not permitted – risk of
fatal injuries.
BSM 2842 / BSM 2882
11
Mount the D-shaped handle.
DANGER
Risk of injury due to electric shock.
Î Disconnect the mains plug before carrying out
any work (e.g. changing the stirrer) on the high-
speed mixer.
DANGER
Risk of poisoning due to toxic gases.
Risk of burns and fire due to flammable gases.
Î Do not process liquids or materials with
unknown hazard potential.
Î Observe the instructions for use issued by the
manufacturer of the material to be stirred.
Î When processing plastics, paints, varnishes
and similar materials, do not work near
flammable gases or materials.
Place the container with the material to be
stirred in a firm, stable position.
Mount the additional handle:
f
2
BSM 287 Additional handle (3)
f
5
BSM 288 Additional handle (6)
f
8
BSM 2863 (110 V / 230 V) Additional
handle (6)
Choose stirrers suitable for the material to be
mixed.
Mount the stirrer, screw the stirrer into the tool
holder (1), and (2) only for BSM 287, until it
stops:
f
1
BSM 287
f
4
BSM 288
f
7
BSM 2863 (110 V / 230 V)
f
BSM 2842 / BSM 2882
10
Switch on the machine at the ON / OFF switch
and set the speed or gear; if empirical values
are not available, start with the lowest speed or
the 1st gear.
Setting the speed:
f
/
BSM 287
1
6
The speed can be continuously adjusted
using the adjusting handwheel (4) on the
handle (5); the handwheel locks in position
at maximum speed.
| 29 |

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Bsm 288Bsm 2842Bsm 2882Bsm 2863

Table des Matières