Additional Safety Rules For Jigsaws; Know Your Product - SPARKY PROFESSIONAL SPARKEYE FSPE 85 Notice Originale

g) if devices are provided for the connection of
dust extraction and collection facilities, en-
sure these are connected and properly used.
Use of dust collection can reduce dust-related haz-
ards.
4. poWer tool Use AnD cAre
a) Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off. Any power tool that can-
not be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing ac-
cessories, or storing power tools. Such preven-
tive safety measures reduce the risk of starting the
power tool accidentally.
d) store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
e) maintain power tools. check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool's operation. if damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f) keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed. Use of the power tool
for operations different from those intended could
result in a hazardous situation.
5. service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
V - Additional safety rules
for jigsaws
WArning: Before connecting a tool to a
power source (mains switch power point receptacle,
outlet, etc.) be sure that the voltage supply is the same
as that specified on the nameplate of the tool. A power
source with a voltage greater than that specified for
the tool can result in serious injury to the user, as well
as damage to the tool. If in doubt, do not plug in the
tool. Using a power source with a voltage less than the
nameplate rating is harmful to the motor.
Original instructions
Your tool is double insulated for additional protection
against a possible electrical insulation failure within the
tool.
Always remove the plug from the mains socket before
making any adjustments or maintenance, including
changing the blade.
▪ Ensure that the lighting is adequate.
▪ Do not use the saw unless the guards are in place.
▪ Keep the shoe flat on the work piece.
▪ Do not put pressure on the saw, such that it slows the
motor down. Allow the saw blade to cut without pres-
sure. You will get better results and you will be taking
better care of your tool.
▪ Keep the area free of tripping hazards.
▪ Do not let anyone under 18 years operate this jigsaw.
▪ Only use blades in good condition.
▪ Before cutting, check that there is sufficient clearance
for the blade under the work piece.
▪ Do not touch the blade after operation. It will be very
hot.
▪ Keep your hands away from under the work piece.
▪ Never use your hands to remove sawdust, chips or
waste close by the blade.
▪ Rags, cloths, cord, string and the like should never be
left around the work area.
▪ Avoid cutting nails. Inspect the work piece and re-
move all nails and other foreign objects before begin-
ning sawing.
▪ Support the work properly.
▪ Never reach over the blade to remove waste or off
cuts.
▪ Do not attempt to free a jammed blade before first
switching off the machine.
▪ If you are interrupted when operating the saw, com-
plete the process and switch off before looking up.
▪ Periodically check that all nuts, bolts and other fixings
are properly tightened.
▪ Do not store materials or equipment above a machine
in such a way that they could fall into it.
▪ Hold power tool by insulated gripping surfaces
only, when performing an operation where the
cutting accessory may contact hidden wiring or
its own cord. Cutting accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
▪ Do not secure the jigsaw upside down in a vice or
work bench and use it as a saw bench. This can lead
to serious injury.
▪ When using the jigsaw, use safety equipment includ-
ing safety goggles or shield, ear defenders, dust mask
and protective clothing including safety gloves.
▪ leave the jigsaw down only after the blade has
come to a standstill. Unattended jigsaw with moving
blade can cause a serious injury.
VI - Know your product
Before using the jigsaw, familiarize yourself with all the
operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
5
en