Configuration Wizard: Tank; Settings Menu; Main Zone; Additional Zone - Daikin EABH16DF6V Manuel D'installation

5 Configuration
5.2.8

Configuration wizard: Tank

This part only applies to systems with an optional domestic hot water
tank installed.
Heat up mode
The domestic hot water can be prepared in 3 different ways. They
differ from each other by the way the desired tank temperature is set
and how the unit acts upon it.
# Code
Heat up mode:
[5.6] [6-0D]
▪ 0:
operation is allowed.
▪ 1: Schedule + reheat: The domestic
hot water tank is heated according to a
schedule and between the scheduled
heat up cycles, reheat operation is
allowed.
▪ 2: Schedule only: The domestic hot
water tank can ONLY be heated
according to a schedule.
See the operation manual for more details.

INFORMATION

Risk of space heating capacity shortage for domestic hot
water tank without internal booster heater: In case of
frequent domestic hot water operation, frequent and long
space heating/cooling interruption will happen when
selecting the following:
Tank > Heat up mode > Reheat only.
Comfort setpoint
Only applicable when domestic hot water preparation is Schedule
only or Schedule + reheat. When programming the schedule, you
can make use of the comfort setpoint as a preset value. When you
later want to change the storage setpoint, you only have to do it in
one place.
The tank will heat up until the storage comfort temperature has
been reached. It is the higher desired temperature when a storage
comfort action is scheduled.
Additionally, a storage stop can be programmed. This feature puts a
stop to tank heating even if the setpoint has NOT been reached.
Only program a storage stop when tank heating is absolutely
undesirable.
# Code
[5.2] [6-0A] Comfort setpoint:
▪ 30°C~[6‑0E]°C
Eco setpoint
The storage economic temperature denotes the lower desired
tank temperature. It is the desired temperature when a storage
economic action is scheduled (preferably during day).
# Code
[5.3] [6-0B] Eco setpoint:
▪ 30°C~min(50,[6‑0E])°C
Installation manual
20
Description
Reheat only:
Only reheat
Description
Description
Reheat setpoint
Desired reheat tank temperature, used:
▪ in Schedule + reheat mode, during reheat mode: the
guaranteed minimum tank temperature is set by the Reheat
setpoint minus the reheat hysteresis. If the tank temperature
drops below this value, the tank is heated up.
▪ during storage comfort, to prioritize the domestic hot water
preparation. When the tank temperature rises above this value,
domestic hot water preparation and space heating/cooling are
executed sequentially.
# Code
[5.4] [6-0C] Reheat setpoint:
▪ 30°C~min(50,[6‑0E])°C
5.3

Settings menu

You can set additional settings using the main menu screen and its
submenus. The most important settings are presented here.
5.3.1

Main zone

Thermostat type
Only applicable in external room thermostat control.
NOTICE
If an external room thermostat is used, the external room
thermostat will control the room frost protection. However,
the room frost protection is only possible if [C.2] Space
heating/cooling=On.
# Code
[2.A] [C–05] External room thermostat type for the
main zone:
▪ 1: 1 contact: The used external room
thermostat can only send a thermo
ON/OFF
separation between heating or cooling
demand.
▪ 2: 2
room thermostat can send a separate
heating/cooling
condition.
5.3.2

Additional zone

Thermostat type
Only applicable in external room thermostat control. For more info
about the functionality, see "Main
# Code
[3.A] [C–06] External room thermostat type for the
additional zone:
▪ 1: 1 contact
▪ 2: 2 contacts
5.3.3 Information
Dealer information
The installer can fill in his contact number here.
# Code
[8.3] N/A Number that users can call in case of
problems.
Description
Description
condition. There is
contacts: The used external
thermo ON/OFF
zone" [ 4 20].
Description
Description
EABH/X16DF6V+9W
Daikin Altherma 3 H W
4P644479-1 – 2020.12
no