Sharp XL-HF202PH Mode D'emploi page 27

Masquer les pouces Voir aussi pour XL-HF202PH:
Table des Matières

Publicité

Using the Radio Data System (RDS) (continued)
■ Information provided by RDS
You can control the RDS by using the buttons on
the remote control only.
Each time the RDS DISPLAY button is pressed, the
display will switch as follows:
Station name (PS)
Frequency
When tuning in to a station other than an RDS station or to
an RDS station which sends weak signal, the display will
change in the following order:
No PS
FM 98.80 MHz
■ Using the Auto Station Programme
Memory (ASPM)
While in the ASPM operation mode, the tuner will auto-
matically search for new RDS stations. Up to 40 stations
can be stored.
1
Press the TUNER button (remote control) or FUNC-
TION button (main unit) repeatedly to select TUNER
function.
2
Press and hold the RDS ASPM button.
After "ASPM" has flashed for about 4 seconds,
1
scanning will start (87.50 - 108.00 MHz).
2
When an RDS station is found, "RDS" will appear
for a short time and the station will be stored in
memory.
3
After scanning, the number of stations stored in
memory will be displayed for 4 seconds, and then
"END" will appear for 4 seconds.
To stop the ASPM operation before it is complete:
Press the RDS ASPM button while it is scanning for stations.
The stations which are already stored in memory will be
kept there.
Programme type (PTY)
Radio text (RT)
No PTY
No RT
E-16
Notes:
● If the same station is broadcasting on different frequen-
cies, the strongest frequency will be stored in memory.
● Any station which has the same frequency as the one
stored in memory will not be stored.
● If 40 stations have already been stored in memory, the
scan will be aborted. If you want to redo the ASPM
operation, erase the preset memory.
● If no station have been stored in memory, "END" will
appear for about 4 seconds.
● If the RDS signals are very weak, station names may
not be stored in memory.
● The same station name can be stored in different
channels.
● In a certain area or during certain time periods, the
station names may be different.
■ Notes for RDS operation
If any of the following events occur, it does not mean
that the unit is faulty:
● "PS", "No PS" and a station name appear alternately,
and the unit does not operate properly.
● If a particular station is not broadcasting properly or a
station is conducting tests, the RDS reception function
may not work properly.
● When you receive an RDS station whose signal is too
weak, information like the station name may not be
displayed.
● "No PS", "No PTY" or "No RT" will flash for about 5
seconds, and then the frequency will be displayed.
Notes for radio text:
● The first 14 characters of the radio text will appear for 4
seconds and then they will scroll across the display.
● If you tune in to an RDS station which is not broadcast-
ing any radio text, "No RT" will be displayed when you
switch to the radio text position.
● While radio text data is received or when the text con-
tents change, "RT" will be displayed.
■ To recall stations in memory
To specify programmed types (news, sports, traffic
programme, etc..) and select stations (PTY search):
1
Press the TUNER button (remote control) or FUNCTION
button (main unit) repeatedly to select TUNER function.
2
Press the RDS PTY button.
"SELECT" and "PTY TI" will appear alternately for about
6 seconds.
3
Within 6 seconds, press the TUNING (
select the programme type.
Each time the button is pressed, the programme type will
appear. If the button is held down for more than 0.5 sec-
onds, the programme type will appear continuously.
or
) button to

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Xl-hf202phsXl-hf202phbkXl-hf302phXl-hf302pht

Table des Matières