Télécharger Imprimer la page

Skil 3620 Notice Originale page 12

Masquer les pouces Voir aussi pour 3620:

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 13
Do not touch the moving sanding sheet
Do not continue to use worn, torn or heavily clogged
sanding sheets
When sanding metal, sparks are generated; do not use
vacuum cleaner and keep other persons and combustible
material from work area
BATTERIES
The battery supplied is partially charged (to ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time)
Only use the following batteries and chargers with
this tool
- SKIL battery: BR1*31****
- SKIL charger: CR1*31****
Do not use the battery when damaged; it should be
replaced
Do not disassemble the battery
Do not expose tool/battery to rain
Permitted ambient temperature (tool/charger/battery):
- when charging 4...40°C
- during operation –20...+50°C
- during storage –20...+50°C
EXPLANATION OF SYMBOLS ON TOOL/BATTERY
3 This tool accepts most commonly available multi-tool
accessories, including existing OIS and Starlock basic
accessories
4 Read the instruction manual before use
5 Batteries may explode when disposed of in fire, so do not
burn battery for any reason
6 Store tool/charger/battery in locations where temperature
will not exceed 50°C
7 Do not dispose of electric tools and batteries together
with household waste material
USE
Charging battery
! read the safety warnings and instructions
provided with the charger
Removing/installing the battery 2
Battery level indicator 8
- press the battery level indicator button M to show the
current battery level.
Changing accessories q
! remove battery from tool
- remove/mount the required accessory as illustrated
- ensure that the openings of the accessory engage into
the tabs of the tool head (any snap-in position possible)
- mount the accessory with the depressed centre
pointing downwards
- loosen/fasten screw B with hex key A
- check the tight seating of the accessory (incorrect
or not securely fastened accessories can come loose
during operation and create a hazard)
Mounting of sanding sheet 9
- tap the dust out of the VELCRO material on sanding
pad E before mounting the sanding sheet
- mount VELCRO sanding sheet H as illustrated
! the dust suction requires the use of perforated
sanding sheets
! perforation in sanding sheet should correspond
with perforation in sanding foot
! replace worn sanding sheets in time
! always use the tool with the total VELCRO surface
covered with sanding paper
Dust suction w
! remove battery from tool
- use vacuum cleaner adapter J only when working with
sanding pad E
- mount vacuum cleaner adapter J as illustrated
- connect vacuum cleaner
! do not use dust extraction device/vacuum cleaner
when sanding metal
- clean vacuum cleaner adapter J regularly for optimal
dust pick-up performance
On/off
- switch on/off the tool by pushing switch C 2 in "I"/"O"
position
! before the accessory reaches the workpiece, the
tool should run at full speed
! before switching off the tool, you should lift it from
the workpiece
Adjusting working speed e
- with wheel D the required oscillating frequency can
be adjusted from low (1) to high (6) (also while tool is
running)
- the optimal working speed depends on the material
and can be determined with practical trials
Holding and guiding the tool
! while working, always hold the tool at the grey-
coloured grip area(s) r
- keep ventilation slots K uncovered
- do not apply too much pressure on the tool (excessive
pressure will cause excessive heat and may shorten
the service life of the accessory)
Battery protection
Switches off the tool or prevents the tool from being
switched on, when
- the load is too high
- the battery temperature is not within the allowable
operating temperature range of -20 to +50°C
- the lithium-ion battery is nearly empty (to protect
against deep discharge)
! do not continue to press the on/off switch after the
tool is switched off automatically; battery may be
damaged
LED-light L t
- LED-light L automatically lights on when activating
switch C
Depth adjustment accessory (DEPTH STOP) (not
standard included) y
APPLICATION ADVICE
For optimal results on different materials use table
u as reference for determining the right accessory
(accessories not standard included)
For more information see www.skil.com
MAINTENANCE / SERVICE
This tool is not intended for professional use
Always keep tool clean (especially ventilation slots K 2 )
! remove battery from tool before cleaning
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
12

Publicité

loading