SOLIS ULTRASONIC PURE 7217 Mode D'emploi page 41

THIN GS W ORT H K NO WI NG A B O UT T H E
▲ ▲
FUN CT IONS OF Y OU R H U MI DI F I E R
ON /OFF B U T T ON ( B)
Once you plug the power plug into the power outlet, a signal sounds and the ap-
pliance switches to standby mode, the LED display lights up briefly and goes out
again. If you touch the ON/OFF button, the LED display and the blue LED light on
the appliance base light up and the humidifier is ready for use. Touch the ON/OFF
button another time and the appliance switches back to standby mode.
HUMI DIF ICATIO N O U TP U T B U TTO N ( C )
With this button, you can adjust the humidification output yourself – choose from 3
output levels: each bar beneath the number represents an output level. Each touch
of the button increases the intensity. If one bar lights up, the lowest output level is
selected. If three bars light up, the highest output level is selected. After the highest
output level, the appliance switches back to the lowest output level if the button is
touched again. If you have not activated the warm mist function, cold mist escapes
from the outlets.
BUTTO N F O R MA N UAL HU M ID I TY S E T T I N G
A N D A U T OMAT IC FU N CTIO N ( D )
Manually setting the humidity:
You can set the desired humidity value by a short touch of this button: The appli-
ance measures the current room temperature, brings it to the set value and then
constantly holds it there. Values between 40% and 80% are possible and can be
adjusted in steps of 5%. Every touch increases the value and is shown in the display.
After 80%, the value jumps back to the neutral setting and then starts again at
40%. After programming, the display goes back to showing the current ambient
humidity resp. temperature. As soon as you have entered a value, the appliance
starts humidifying for at least 2 minutes, regardless of whether the set value is above
or below the actual room humidity. The appliance switches off after these 2 minutes
have elapsed, provided the actual room humidity lies above the set value.
An example: If you set a room humidity of 50%, the appliance checks the ambient
humidity for 2 minutes while humidifying at the same time. Should the room hu-
midity lie under the set 50% (minus tolerance) after the 2 minutes have elapsed,
the humidifier keeps working. Should the room humidity be at 50% or above, the
appliance stops working.
The appliance is equipped with a built-in humidity switch, guaranteeing
that user programmed air humidity is permanently maintained. The humid-
ity switch checks the humidity constantly at intervals of 10 seconds. Should
the effective humidity fall 5% under the value chosen by you, the appliance
switches on. This tolerance is picked deliberately to keep the appliance from
turning on and off frequently and disturbingly.
80
In our example this would mean: Should the room humidity fall under 45%, the
appliance would switch back on 10 seconds later and restore the humidity to 50%.
Note: When the appliance is turned on (regardless of whether the power
supply has been disrupted or not) it will start operating for at least 2 minutes
to meter current air humidity, even if effective air humidity is above the set
value. After that, the appliance will either keep operating – if the value is
below 45%, as in our example – or discontinue operation – if the value is
above 50%, as in our example.
Memory function:
If the air humidifier is turned on and power has not been disconnected since last
programming of air humidity, the programmed value is saved and the appliance will
humidify the air of the room according to this last programmed value.
If the power supply has been interrupted, the previously set humidity value is de-
leted. In this case, the appliance humidifies up to the factory-set standard value
of 68% and would require reprogramming by yourself should another value be
desired.
Setting the automatic function:
If you touch the -button for 3 seconds, the appliance switches to automatic
mode. The appliance registers the current room humidity and brings resp. keeps
the humidity constant between 55% and 68%. The appliance selects the functions
optimal for this purpose itself, depending on the current ambient temperature and
humidity. No manual settings for room humidity or humidification output can be
made in this function.
WAR M M IS T FU NC T ION B U TT ON (E )
When you touch this button, you can activate the warm mist function. You can also
increase or decrease the humidification output within the 3 possible intensities with
the button in the warm mist function.
Please note: The higher the humidification output setting is in the warm mist func-
tion, the warmer the steam is. The warmer the steam is, the higher is the humidi-
fication output in turn. Therefore, the humidification output is generally higher for
warm mist than for cold mist.
If you touch the button another time, you can switch the warm mist function off
again, making the appliance only work with cold mist.
81