S+S Regeltechnik THERMASGARD FSTF Notice D'instruction page 10

G
®
THERMASGARD
A room temperature sensor THERMASGARD
room control and operating panel with temperature sensor, push-buttons, potentiometers, status indicators (LEDs). The in-wall sensor is mounted
in high-quality panel switch programmes, ideally of the brands Gira, Berker, Merten, Jung, Siemens or Busch-Jaeger (using in-wall adapters) either
individually or in combination with light switches, socket outlets, etc.It is used in non-aggressive, dust-free environments, in refrigeration, air
conditioning and clean room technology, and in interior rooms, such as living rooms, offices, hotels, etc.
TECHNICAL DATA
Measuring ranges: –30...+60 °C
Sensor ⁄ output: see table, assembled on board, passive
Range suppression: in the button
Testing current: see page 15
Potentiometers: standard 1 kΩ, max. 0.1 W (other ratings optional on request,
e. g. 100 Ω, 2.5 kΩ, 5 kΩ, 10 kΩ optional 0 -10 V linear)
Turn switches: max. 24 V AC ⁄ DC, max. 130 mA, max. 5 steps (0, Auto, I, II, III)
Rocker switch: max. 24 V AC ⁄ DC, max. 130 mA
Push-buttons: normally open contact, max. 24 V DC ⁄ 10 mA
LEDs: max. 24 V DC (optional max. 24 V AC),
standard green (red, yellow or two-colour optional)
Installation: in in-wall flush box Ø 55 mm
Electrical connection: via plug terminals, 0.14 - 1.5 mm²,
on safety extra-low voltage only, max. 42 V AC, 60 V DC
Humidity: max. 90 % r.H., non-precipitating air
Protection class: III (according to EN 60 730)
Protection type: IP 20 (according to EN 60 529)
S W I T C H P R O G R A MME S
Manufacturer: GIRA System 55 (other switch programmes, manufacturers,
colours and prices upon request
Housing: plastic, standard colour pure white, glossy (similar to RAL 9010)
(other colours are possible on request with colour variants
depending on the respective light switch programme)
THERMASGARD ®
FSTF 1
Standard version with sensor
®
THERMASGARD FSTF 1
Type ⁄ WG01
FSTF1
F S T F1 P t10 0
F S T F1 P t10 0 0
F S T F1 Ni10 0 0
F S T F1 Ni T K
F S T F1 L M 2 3 5 Z
F S T F1 N T C1,8 K
F S T F1 N T C10 K
F S T F1 N T C 2 0 K
FSTF
® FSTF is used for air temperature measurement or setpoint adjustment, for presence detection or as
Room temperature sensors
Sensor ⁄ Output
passive
Pt100 (according to DIN EN 60 751, class B)
Pt1000 (according to DIN EN 60 751, class B)
Ni1000 (according to DIN EN 43 760, class B, TCR = 6180 ppm ⁄ K)
Ni1000 TK5000 (TCR = 5000 ppm ⁄ K), LG - Ni1000
LM235Z (TCR = 10 mV ⁄ K; 2.73 V at O °C), KP10
NTC 1.8 K
NTC 10K
NTC 20K
1x two-wire connection
standard
1x two-wire connection
LM 235 Z (KP 10)
Connecting diagram
10
Rev. 2021 - V14
5 5
4
4
3
3
2 2 1 1
Item No.
IP 20 (–30...+60 °C)
1101- 5020- 1000-162
1101-5020- 5000- 162
1101-5020- 9000- 162
1101-5021- 0000- 162
1101-5022- 1000- 162
1101- 5021-2000- 162
1101- 5021-5000- 162
1101- 5021-6000- 162
FSTF 1 - U
6
6
7
7