Dremel 7700 Traduction De La Notice Originale page 13

SAFETY WARNINGS SPECIFIC FOR
WIRE BRUSHING OPERATIONS
a. Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
b. If the use of a guard is recommended for wire brushing,
do not allow any interference of the wire wheel or
brush with the guard. Wire wheel or brush may expand in
diameter due to work load and centrifugal forces.
c. Do not exceed 15000 min
Do not work with materials containing
WARNING
!
asbestos (asbestos is considered
carcinogenic).
Take protective measures during work
WARNING
!
when dust can develop that is harmful
to one's health, combustible or explosive (some dusts are
considered carcinogenic); wear a dust mask and work with
dust/ chip extraction when connectable.
ENVIRONMENT
DISPOSAL
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into household waste!
According the European Guideline 2002/96/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that
are no longer usable must be collected separately and
disposed of in an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Voltage Rating
. . . . . . . . . . . . . . .
Amperage Rating
. . . . . . . . . . . .
No Load Speed
. . . . . . . . . . . . . . .
Collet Capacity
. . . . . . . . . . . . . . .
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5 Amps.
ASSEMBLY
ALWAYS TURN OFF THE TOOL BEFORE CHANGING ACCESSORIES,
CHANGING COLLETS, OR SERVICING THE TOOL.
when using wire brushes.
-1
7,2V
0,7Ah
n
10000/20000 min
-1
o
0,8mm, 1,6mm, 2,4mm, 3,2mm
The Dremel multitool is a high quality precision tool that can be
used to perform detailed and intricate tasks. The wide range of
Dremel accessories and attachments allow you to perform a large
variety of tasks. These include tasks such as sanding, carving and
engraving, cutting, cleaning and polishing.
PICTURE 1
PICTURE 2
A. Collet Nut
B. Collet
C. Housing Cap
D. Shaft Lock Button
E. Grip
F. Ventilation Openings
G. On/Off Switch and Speed Dial
H. Release Tab
I. Battery
J. Charger
CHARGING THE TOOL
The Cordless Rotary Tool is not fully charged. The tool is equipped
with a removable battery pack. Be sure to charge pack prior to
initial use.
To charge the tool:
1. Put the switch in the "OFF" position. PICTURE 2
2. Squeeze the release tabs on both sides of the battery pack
and remove pack from back of tool. PICTURE 2
3. Align exterior shape of battery pack with exterior shape of
charger (arrows on battery will point to the arrows located
on charger), squeeze release tabs, insert battery pack into
charger and release pressure on tabs so it locks in place.
4. Plug charger into the power source. The green LED light
indicates connection has been made and the battery pack is
charging. Under normal use the tool requires 3 hours charging
time to reach full capacity.
5. When charging is completed, squeeze release tabs and
remove battery pack from charger.
6. Align exterior shape of battery pack with exterior shape of the
housing of tool. Squeeze release tabs, insert battery pack into
back of tool and release so it locks in place."
IMPORTANT CHARGING NOTES
1. The battery pack accepts only about 80% of its maximum
capacity with its first few charge cycles. However, after the
first few charge cycles, the battery will charge to full capacity.
2. The charger was designed to fast charge the battery only
when the battery temperature is between 4 ºC and 41 ºC.
3. A substantial drop in operating time per charge may mean
that the battery pack is nearing the end of its life and should
be replaced.
NOTE: Use of chargers or battery packs not sold by Dremel will void
the warranty.
13
GENERAL