Festool OF 1010 Q Notice D'utilisation D'origine page 12

ther the machine is in operation or in neutral
position.
Temperature control
To prevent overheating, the safety electronics
switches the machine off when it reaches a cri-
tical motor temperature. Let the machine cool
down for approx. 3-5 minutes before using it
again. The machine requires less time to cool
down if it is running, i.e. in neutral position.
Brake (OF 1010 EBQ)
The OF 1010 EBQ has an electronic brake which
brings the spindle with tool to a standstill within
approx. 2 seconds of the tool being switched
off.
5.2 Changing tools
You can turn the machine upside down when
changing the tool.
a) Inserting the tool
- Insert the router into the open clamping collet
as far as possible, but at least up to the mark
( ) on the router shank.
- Turn the spindle until the spindle stop (1.14)
catches when pressed and the spindle is lo-
cked in place.
- Tighten the locking nut (1.13) with a 19 mm
open-end spanner.
b) Removing the tool
- Turn the spindle until the spindle stop (1.14)
catches when pressed and the spindle is lo-
cked in place.
- Loosen the locking nut (1.13) using a 19 mm
open-ended spanner until a resistance is felt.
Overcome this resistance by turning the open-
ended spanner even further.
- Remove the cutter.
5.3 How to change the clamping col-
let
Clamping collets are available for following
shank diameters: 6.35 mm, 8 mm, 9.53 mm,
10 mm, 12 mm, 12.7 mm (order numbers see
Festool catalogue or Internet „www.festool.
com".
- Fully unscrew the nut (1.13) and remove from
spindle together with the clamping collet.
- Insert a new clamping collet with nut into the
spindle and slightly tighten the nut. Do not
tighten the nut until a milling cutter has been
fi tted.
5.4 Adjusting the milling depth
The milling depth is adjusted in three stages:
a) Setting the zero point
- Open the clamping lever (1.6) so that the stop
cylinder (1.7) can move freely.
- Place the router with router table (1.11) onto a
smooth surface. Open the rotary knob (1.15)
and press the machine down until the milling
cutter rests on the base.
- Clamp the machine in this position by tighte-
ning the rotary knob (1.15).
- Press the stop cylinder against one of the
three sensing stops of the pivoted turret stop
(1.9).
The individual height of each sensing stop can
be adjusted with a screwdriver:
Sensing stop
A
B
C
- Push the pointer (1.4) down so that it shows
0 mm on the scale (1.5).
b) Setting the milling depth
The desired milling depth can be set either with
the quick depth adjustment or with the fi ne
depth adjustment.
• Quick depth adjustment: Pull the stop
cylinder (1.7) up until the pointer shows the
desired milling depth. Clamp the stop cylin-
der in this position with the clamping lever
(1.6).
• Fine depth adjustment: Clamp the stop cy-
linder with the clamping lever (1.6). Set the
desired milling depth by turning the adjusting
wheel (1.3) in. Turn the adjusting wheel to the
next mark on the scale to adjust the milling
depth by 0.1 mm. One full turn adjusts the
milling depth by 1 mm. The maximum ad-
justment range with the adjusting wheel is 8
mm.
c) Increasing the milling depth
- Open the rotary knob (1.15) and press the
tool down until the stop cylinder touches the
sensing stops.
- Clamp the machine in this position by tighte-
ning the rotary knob (1.15).
5.5 Dust extraction
Always connect the machine to a dust
extractor. A connection for extracting
dust and chips (1.8) is a standard fea-
ture on the routers.
At the same time a chip guard (2.2) on the side
stop prevents fl ying chips.
With edge routing, the best extraction effect is
obtained with the extractor hood AH-OF, avai-
lable as an accessory.
KSF-OF chip catcher
Using the KSF-OF chip catcher (9.1) (some-
times included in the scope of delivery), the
effi ciency of the extraction can be increased
when routing edges.
Installation is similar to that of the copying
ring.
The hood can be cut off along the grooves (9.2)
using a hacksaw and can thus be reduced in
size. The chip catcher can then be used for
interior radiuses up to a minimum radius of
40 mm.
12
min. height/max. height
38 mm/44 mm
44 mm/54 mm
54 mm/67 mm