Clatronic LSM 3128 Mode D'emploi page 26

Preparations
1. Remove the motor device and the accessories from the box.
Also remove any packaging materials that may be present.
2. Installing the motor device
WARNING:
The safety distance (see diagram) from the edge of
the bathtub to the motor device must be at least 60
centimetres!
Never place the device within this zone or above the
bathtub!
The device must be at least 30 centimetres above the
fl oor. Ideal surfaces are non-upholstered chairs or stools.
Do not use any supporting surfaces on rollers, as these
could be pulled towards the bathtub by mistake.
3. Wall Installation
The motor device can also be mounted on the wall. Please
note the information given under section 2 above.
In order to mount the motor device on the wall, measure
the distance between the two indentations on the back of
the motor device and then drill two holes horizontally at this
distance apart. Please ensure beforehand that you will not
damage any electric cables that are hidden in the wall! Then
insert rawlplugs and screws into the drilled holes. Then
position the motor device over the screws and check that it
is fi rmly in place.
NOTE:
The motor device should be within your fi eld of vision so
that the remote control will work and you can read the
settings.
4. Unfold the whirlpool mat and fi x it to the fl oor of the bathtub.
The hose connection must be facing the water outlet pipe.
5. Hose connection
NOTE:
The air hose has two ends of different colours (see
diagram 3). Use the end with the peg for connection to the
motor device.
The connection is locked in place by turning the hose
through approximately 15° in a clockwise direction. Insert
the other end of the hose into the opening on the whirlpool
mat.
6. Fill the bathtub in the usual manner with water.
WARNING:
Do not use any salts or strongly foaming additives in the
bath!
Initial Operation and Use
• Unwind the mains lead completely.
• Insert the plug into a properly installed 230 V, 50 Hz power
socket.
26
05-LSM 3128 Neu.indd 26 05-LSM 3128 Neu.indd 26
WARNING:
Avoid operating the motor device with wet hands. Place
the remote control somewhere within your reach before
you get into the bath.
• Please use an infl atable neck pillow if necessary.
• After you have sat down in the bath, switch on the device
using the POWER button on your remote control.
• You can now use the remote control to select a switch-off
time of between 15 and 60 minutes and a whirlpool strength
between High (HI), Medium (MED) and Low (LO) (see
diagram 2).
NOTE:
The fi rst few times you use the device you should not
exceed a bathing time of 15 minutes. You can extend this
time subsequently depending on how well you tolerate the
whirlpool.
• If you would like to stop the whirlpool, switch the motor off
using the POWER button on your remote control.
WARNING:
Remove the power cable from the socket only after you
have dried yourself completely.
Cleaning and Storage
• Remove the mains plug from the socket.
• Disconnect the hose and the whirlpool mat from the motor
device. Clean these accessories in soapy water using a
hand shower. Any residues on the mat can be removed with
a soft brush.
NOTE: After use:
• Do not allow any water back into the air chambers of
the whirlpool mat.
• If necessary, allow the water to drain out again
through the air holes of the whirlpool mat.
• Hang the whirlpool mat up until it is completely dry.
• The housing of the motor device can be wiped off with a
slightly moistened cloth.
CAUTION:
Do not immerse the motor device in water!
• Allow the accessories to dry before you put them away. The
whirlpool mat can be folded together again to save space.
Remote Control Batteries
The battery of the remote control is a long-life lithium cell. If
the range of the remote control is reduced during use, please
proceed as follows:
• Open the battery compartment on the back of the remote
control.
• Replace the cell by a battery of the same type. Ensure cor-
rect polarity (see the fl oor of the battery compartment or the
imprint on the outside).
• Then close the battery lid.
19.11.2008 9:42:55 Uhr 19.11.2008 9:42:55 Uhr