Powerworks 2100413 Manuel D'utilisation page 5

EN
DE ES IT FR PT NL RU FI SV NO DA PL CS SK SL HR HU RO BG EL AR TR HE LT LV ET
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal in-
jury.
Only the parts shown on the parts list are intended to be re-
paired or replaced by the customer. All other parts should
be replaced at an Authorised Service Centre.
To avoid serious personal injury, always remove the bat-
tery pack from the tool when cleaning or performing any
maintenance.
SPOOL REPLACEMENT See Figure 9.
Use original manufacturer's replacement cutting line for
best performance.
„ Remove the battery pack.
„ Push in tabs on side of spool cover.
„ Pull spool cover up to remove.
„ Remove the old spool.
„ To install the new spool, make sure the cutting line is
captured in the slot on the new spool. Make sure the
end of the cutting line is extended approximately 15cm
beyond the slot.
„ Install the new spool so that the cutting line and slot
align with the eyelet in the cutting head. Thread the
cutting line into the eyelet.
„ Pull the cutting line extending from the cutting head so
the cutting line releases from the slot in the spool.
„ Reinstall the spool cover by depressing tabs into slots
and pushing down until spool cover clicks into place.
CUTTING LINE REPLACEMENT See Figures 9.
„ Line up the slots on the spool cap (A) with the slots on
the string head (B).
„ Insert line through the string head hole (C). Push line
until it exits the opposite string head hole.
„ Pull the line through until there is an equal amount of
line on each side.
„ Turn the spool cap (D) clock-wise to begin winding
English (original instructions)
WARNING
WARNING
the string into the string head. Leave approximately 5
inches of string protruding out of each side of the head.
ASSEMBLY THE BRUSH CUTTER See Figure 10.
Warning: Be careful of sharp edges and to wear gloves.
„ Remove the battery pack.
„ Ensure the 'F' is installed on the shaft of the trimmer.
„ Insert a suitable screw driver through the two holes.
„ Place the Brush-cutter Blade 'G' on top of the spacer 'F'
ensuring it is centered.
„ Place washer 'H on top of the Brush-cutter Blade 'G'
„ Place cover 'I' over washer 'H'
„ Using a 19mm or 3/4" wrench tighten the lock-nut 'J'
Counter-clockwise to 44-58" N.M or 32-42 ft/lbs of
torque.
„ Spin the Brush-cutter Blade 'B' to ensure Brushcutter
Blade is secured tightly.
STORING THE TRIMMER
„ Remove the battery pack from the trimmer before
storing.
„ Store it in a place that is inaccessible to children.
„ Keep away from corrosive agents such as garden
chemicals and de-icing salts.
„ Store and charge your batteries in a cool area.
Temperatures
temperature will shorten battery pack life.
„ Store the battery pack where the temperature is below
27˚C and away from moisture.
„ All batteries gradually lose their charge. The higher the
temperature, the quicker they lose their charge. If you
store your unit for long periods of time without using
it, recharge the batteries every month or two. This
practice will prolong battery pack life.
„ Secure the trimmer during transport to prevent damage
or injury. Clean and maintenance before storage, use
of guards on cutting attachments with metal blades.
Use of cover for metal blades during transport and
storage.
ENVIRONMENTAL PROTECTION
„ Environmental protection should be a priority of
considerable importance when using the machine,
for the benefit of both social coexistence and the
environment in which we live. Try not to cause any
disturbance to the surrounding area.
„ Scrupulously comply with local regulations for the
4
above or below normal room