Safety; Specifications - Titan Tool HVLP Transfer Pump 0524038 Notice D'utilisation

Important Safety Information
This symbol indicates a hazardous situation, which, if
not not avoided could result in death or serious injury.
To reduce the risks of fire or explosion, electrical shock
and the injury to persons, read and understand all
instructions included in this manual. Be familiar with
the controls and proper usage of the equipment.
HAZARD: EXPLOSION HAZARD DUE TO
INCOMPATIBLE MATERIALS
Will cause property damage or severe injury.
PREVENTION:
• Do not use materials containing bleach or chlorine.
• Do not use halogenated hydrocarbon solvents such as bleach,
mildewcide, methylene chloride and 1,1,1 - trichloroethane.
They are not compatible with aluminum.
• Contact your coating supplier about the compatibility of
material with aluminum.
HAZARD: GENERAL
Can cause severe injury or property damage.
PREVENTION:
• Read all instructions and safety precautions before operating
any equipment.
• Follow all appropriate local, state, and national codes
governing ventilation, fire prevention, and operation.
• The United States Government Safety Standards have been
adopted under the Occupational Safety and Health Act
(OSHA). These standards, particularly Part 1910 of the General
Standards and Part 1926 of the Construction Standard should
be consulted.
• Use only manufacturer authorized parts. User assumes all risks
and liabilities when using parts that do not meet the minimum
specifications and safety devices of the manufacturer.
• Before each use, check all hoses for cuts, leaks, abrasion or
bulging of cover. Check for damage or movement of couplings.
Immediately replace the hose if any of these conditions exist.
Never repair a hose. Replace it with an identical replacement
hose.
• Do not spray outdoors on windy days.
• Wear clothing to keep paint off skin and hair.
• Never aim the spray gun at any part of the body.
HAZARD: EXPLOSION OR FIRE
Solvent and paint fumes can explode or ignite. Property
damage and/or severe injury can occur.
PREVENTION:
• Exhaust and fresh air introduction must be
provided to keep the air within the spray area
free from accumulation of flammable vapors.
• Turbine contains sparking parts. Turbine must
be placed in a well ventilated area at maximum distance from
the spray area.
• Avoid all ignition sources such as static electricity, open
flames, pilot lights, hot objects, cigarettes, and sparks from
connecting and disconnecting power cords and working light
switches.
• Use extreme caution when using materials with a flashpoint
below 100° F (38°C). A fluid's flashpoint is the temperature at
English
·
Read all safety information before operating
the equipment. Save theSe InStRuctIonS.
HAZARD:
Paints, solvents, insecticides, and other materials can be harmful if
inhaled or come in contact with the body. Vapors can cause severe
nausea, fainting, or poisoning.
PREVENTION:
HAZARD:
May cause severe injury.
PREVENTION:
Service
Should your spray system need service during the warranty period,
return your unit and the proof of purchase to the distributor where it
was purchased. At our option, the unit will be repaired or replaced.
In a continued commitment to improve quality, we reserve the right
to make component or design changes when necessary.
IMPORTANT: Never operate unit for more than ten seconds
without fluid. Operating this unit without fluid will cause
unnecessary wear to the seal.

Specifications

Max working flow rate ........20 fl oz./min at 35 PSI
Max flow rate flushing
(Free flow) ...............................40 fl oz./min
Maximum working
pressure ...................................35 PSI (2.4 MPa)
Power ........................................PMDC brushed motor, 120 VAC, 60 Hz, 0.40
Weight ......................................3.3 lbs (1.5 kg)
Hose length ............................30 ft (9.1 m)
2
which vapors from the fluid could ignite if exposed to a flame
or spark.
• Fire extinguishing equipment must be present and in working
order.
• The power cord must be connected to a grounded circuit.
• Follow the material and solvent manufacturer's safety
precautions and warnings.
HAZARDOUS VAPORS
• Use a respirator or mask if vapors can be inhaled.
Read all instructions supplied with the mask to
be sure it will provide the necessary protection.
• Wear protective eyewear.
• Wear protective clothing as required by coating manufacturer.
ELECTRIC SHOCk HAZARD
• Never immerse electric parts in water or any other liquid.
Wipe the exterior of the pump with a damp cloth for cleaning.
Always make sure the pump is disconnected from the turbine
before taking it apart for cleaning and/or service.
A
© Titan Tool. All rights reserved.