Wolf Garten BLUE POWER 34 E Notice D'instruction D'origine page 12

Set cut height
1
Attention! Rotary cutter blade
Undertake work/adjustments on the equipment only after the
motor is switched off and the cutting tool has come to a
standstill.
z Switch off motor and pull out power plug.
1. Pull the lever out L (1).
2. Set the desired cutting height
3. Press the lever back in
Selection of Cutting height
z If possible, mow when grass is dry in order to protect turf. Do not
se cutting position too low when mowing very hight or wet grass.
z We recommend an average cutting height of 40 mm.
Connecting to the mains (230 Volts, A.C., 50 Hz)
z The mower operates from any normal household mains supply,
provided with a 16 Amps. fuse.
3
Note: Residual current protection device
These protection devices safeguard while touching damaged
wires, from insulation flaws and in certain cases, also while
damaging live wires.
z We recommend that the equipment only be plugged into a
power socket, which is protected by a residual current
protection device (RCD) with a residual current of not more
than 30 mA.
z Retrofit kits are available for old installations. Consult an
electrician.
Starting and Stoping
z Switch on motor with mowerplaced on level and firm ground.
z not in high grass - alternatively tilt slightly
N
Switch-on motor
1. Depress button and hold (1).
2. Lift up bar (2).
3. Release bar (1).
Switch-off motor N
z Release bar (2).
Tips for mowing
z To prevent strips of grass from being left unmowed, the cutting
paths must always overlap a few centimeters
z Always let cable trail on the cut side of the lawn.
Cut / Collect
Activate cut/collect function
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the motor
is switched off and the cutting tool has come to a standstill.
z Do not start the motor until your feet are at a safe distance
from the cutting tool.
1. Remove the grass collecting bag.
2. Turn the switch to "CUT/COLLECT".
3. Hang up the collection bag if necessary.
4. Start the motor.
12
L (2).
L
(3).
M .
O
.
L (4)
Hang up collection bag
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the motor
is switched off and the cutting tool has come to a standstill.
z Do not attach the collection bag until your feet are at a safe
distance from the cutting tool.
1. Lift the protective flap.
2. Hang the grass bag in the chassis with the hooks in the recesses
(see arrow).
3. Replace the protective flap.
Emptying of Grassbox
When the collection bag is full, the flap lowers by itself
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the motor
is switched off and the cutting tool has come to a standstill.
z Switch off motor and pull out power plug.
z Empty collection bag
z Remove potential blockages in the cutting space before
starting.
3
Instructions for level indicator:
For an efficient functioning of the level indicator, regularly clean
the holes under the level indicator in the collection bag with a
hand brush.
Mulch
„Mulching" is a process in which the grass is finely chopped by a spe-
cial cutting system and then deposited on the ground. The result is
that the grass does not have to be collected and disposed of. „Mul-
ching" also prevents the lawn from drying out.
3
Instructions for mulching
We recommend:
z Depending on the growth of grass, mulch 1 – 2 x per week
z The grass should not be too high nor too wet!
z Go slow while mulching
z Take care that the blade channels do overlap.
z Do not cut grass more than 20 mm.
3
Note:
Mulching is not advisable in case of moss-affected or
entangled grass, because the cut material stays on the moss
surface and/or entanglement and thus cannot be absorbed by
the ground.
z Regularly scarify and manure the lawn.
Activating the mulch function
1
Attention! Rotary cutter blade
Undertake adjustments on the equipment only after the motor
is switched off and the cutting tool has come to a standstill.
z Do not start the motor until your feet are at a safe distance
from the cutting tool.
1. Remove the grass collecting bag.
2. Set the switch to „MULCH".
3. Start the motor.
P
Q
R .
L (4)
.
G