Bluetooth; Troubleshooting - ADVANCED NATIVE TECHNOLOGIES ANTMIX 16fx usb Notice D'emploi

SERIES
3.1.5 | OPTIONAL BLUETOOTH & MP3 PLAYER BOARDS
®
BOARDS INSTALLATION
The installation is very simple, but if you have no experience, contact a specialized service center.
WARNING: for your safety, operate turning off the mixer and unplugging the appliance from the mains socket.
With a flat-headed screwdriver, press gently under the plastic cover and pry up the right side to remove it carefully. (Fig.1)
To install the optional MPX 1624 or BTX 1624 card, connect the 5-pin connector cable to the respective 5-pin connector
on the printed circuit board of the mixer. (Fig.2). At this point it is sufficient to hook the optional module in the appropriate
housing and take advantage of the new functions.
Fig.1

BLUETOOTH

MODULE - BTX 1624
®
Activate the Bluetooth interface of your device and press the PAIR button of the board. The source device should
®
recognize the board as BT 4.0 and synchronize automatically.
In the mixer, press the 2TK TO MAIN MIX selector, then gradually raise the 2TK LEVEL knob and the MAIN MIX fader
until you reach the desired volume.
You can also control the volume from the Bluetooth
and PAUSE the key you can choose the track to listen to or pause it
MP3 PLAYER MODULE - MPX 1624
In a USB stick, load all the tracks you want (up to 32Gb), even in multiple folders. Insert the stick into the USB port of
the optional board by simply pressing the PUSH & HOLD button for 2 seconds to start playing the ladder from the first
track. The display will alternately show the number of the file and its folder.
To listen to the previous song just press , while to listen to following track press
can change the folder. The key pause or resume the song, if you press stop
If you press more times the key, you can choose random play, a single song play or all tracks play.
In the mixer, please press the 2TK TO MAIN MIX selector, then gradually raise the 2TK LEVEL knob and the MAIN MIX
fader until you reach the desired listening volume.
ANTMIX Series
12 User manual |
Fig.2
card itself, using the VOL- and VOL+ keys, using the
®
; holding down the keys you
playback will be totally stopped.

4 | TROUBLESHOOTING

PROBLEM LED
Power LED turned off.
Power LED turned on, but MAIN MIX low.
Power LED turned on, MASTER VOL raised, but
MUTE button depressed.
No sound or very
low sound level
Power LED turned on, MASTER VOL raised, but
input channel LEVEL low.
Power LED turned on, MASTER VOL raised,
LEVEL raised, but +48V off.
Power LED turned on, MAIN MIX raised but,
signal addressed to GR1-2 or GR3-4 are not
addressed to MAIN MIX
DFX MUTE activate
No effects heard
DFX MUTE deactivated
No FX signal in
DFX MUTE deactivated
monitors
Distortion PEAK LED lit.
Confused sound
Recorded signal is
not heard
No recording
Loop in recording
SOLUTION
Make sure the device is properly connected to the mains
outlet.
Raise MAIN MIX level.
Raise MUTE button.
Check connections between sources and mixer. Raise
channel LEVEL.
Activate +48V power for microphones deserving it.
Press the L-R button over GR1, GR2, GR3 and/or GR4
faders
Turn off the DFX MUTE button, anc check send levels of all
the channels.
Check the levels of DFX RETURN as well as GR1-2, GR3-4
and MAIN MIX assign buttons.
Check DFX TO AUX 1 and DFX TO AUX 2 knobs levels
Reduce the level of the inputs and/or MAIN MIX
Check you haven't connected a line signal into a MIC
socket..
Make sure you haven't simultaneously activated more
sound sources in the same channel
Check if you activated microphones LOW CUT filter
Check that LINE/USB selectors of the stereo channel 15-16
(ANTMIX 16FX USB) or 23-24 are not addressed to MAIN
MIX while you're listening to USB signal via MAIN MIX.
Check that LINE/USB selectors of the stereo channel
15-16 (ANTMIX 16FX USB) or 23-24(ANTMIX 24FX USB)
is pressed and that PLAYBACK selector is addressed to
desired output (MAIN or GR1-2)
Check that PLAYBACK selector is addressed to desired
output (MAIN or GR1-2) and that desired signal are
addressed to the right destination.
LINE/USB stereo channel 15-16 (ANTMIX 16FX USB) or
23-24 (ANTMIX 24FX USB) is pressed and the PLAYBACK
selector is addressed to the wrong oputput (MAIN or
GR1-2)
ANTMIX Series
| User manual
13